Digital indicator conductor AER-102-Ech (high concentration)
Shinko Technos Co., Ltd.

Aer-102-Ech, C5

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

Temperature: ± 1 ℃

Conductive zero adjustment coefficient setting range: See item in the measurement range

Calibration range: -10.0 ~ 10.0 ℃

・ Relay contact 1A
・ Control capacity: 3A 250V AC (resistance load), 1A 250V AC (induced load COSφ = 0.4)
・ Electrical life: 100,000 times
・ Control operation: P operation, ON/OFF operation

-Denstrual rate, temperature, and MV are converted to analog amount for each input sampling and output by current. (Factory shipping: Conductive)

・ If the transmission output 1 maximum value and transmission output 1 are set to the same value, the transmission output 1 is 4 ma DC fixed.
・ The transmission output volume can be displayed.

・ Dusive ability: 12000 ・ Current: 4 to 20mA DC (maximum load resistance 550Ω) ・ Output accuracy: within ± 0.3%of transmission output 1 span

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ Control board embedded method (compatible panel thickness 1 ~ 8mm)
・ Case: flame -retardant resin color: black
・ Panel: Membrane sheet
・ Drip -proof / dustproof structure: front IP66

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W48XH96XD110mm case depth: 98.5mm (at panel mount)

Approximately 280g

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9600, 19200, 38400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

Aer-102-Ech, EVT3

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

・ Conductive: ± 0.5%of measuring range span ・ Salt conversion: Measurement range span ± 1%・ TDS conversion: measuring range span ± 1.5%

Temperature: ± 1 ℃

Conductive zero adjustment coefficient setting range: See item in the measurement range

Calibration range: -10.0 ~ 10.0 ℃

・ Relay contact 1A
・ Control capacity: 3A 250V AC (resistance load), 1A 250V AC (induced load COSφ = 0.4)
・ Electrical life: 100,000 times
・ Control operation: P operation, ON/OFF operation

-Denstrual rate, temperature, and MV are converted to analog amount for each input sampling and output by current. (Factory shipping: Conductive)

・ If the transmission output 1 maximum value and transmission output 1 are set to the same value, the transmission output 1 is 4 ma DC fixed.
・ The transmission output volume can be displayed.

・ Dusive ability: 12000 ・ Current: 4 to 20mA DC (maximum load resistance 550Ω) ・ Output accuracy: within ± 0.3%of transmission output 1 span

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ Control board embedded method (compatible panel thickness 1 ~ 8mm)
・ Case: flame -retardant resin color: black
・ Panel: Membrane sheet
・ Drip -proof / dustproof structure: front IP66

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W48XH96XD110mm case depth: 98.5mm (at panel mount)

Approximately 280g

Aer-102-Ech, TA2

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

Temperature: ± 1 ℃

Conductive zero adjustment coefficient setting range: See item in the measurement range

Calibration range: -10.0 ~ 10.0 ℃

・ Relay contact 1A
・ Control capacity: 3A 250V AC (resistance load), 1A 250V AC (induced load COSφ = 0.4)
・ Electrical life: 100,000 times
・ Control operation: P operation, ON/OFF operation

-Denstrual rate, temperature, and MV are converted to analog amount for each input sampling and output by current. (Factory shipping: Conductive)

・ If the transmission output 1 maximum value and transmission output 1 are set to the same value, the transmission output 1 is 4 ma DC fixed.
・ The transmission output volume can be displayed.

・ Dusive ability: 12000 ・ Current: 4 to 20mA DC (maximum load resistance 550Ω) ・ Output accuracy: within ± 0.3%of transmission output 1 span

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ Control board embedded method (compatible panel thickness 1 ~ 8mm)
・ Case: flame -retardant resin color: black
・ Panel: Membrane sheet
・ Drip -proof / dustproof structure: front IP66

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W48XH96XD110mm case depth: 98.5mm (at panel mount)

Approximately 280g

Aer-102-Ech1, C5

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

Temperature: ± 1 ℃

Conductive zero adjustment coefficient setting range: See item in the measurement range

Calibration range: -10.0 ~ 10.0 ℃

・ Relay contact 1A
・ Control capacity: 3A 250V AC (resistance load), 1A 250V AC (induced load COSφ = 0.4)
・ Electrical life: 100,000 times
・ Control operation: P operation, ON/OFF operation

-Denstrual rate, temperature, and MV are converted to analog amount for each input sampling and output by current. (Factory shipping: Conductive)

・ If the transmission output 1 maximum value and transmission output 1 are set to the same value, the transmission output 1 is 4 ma DC fixed.
・ The transmission output volume can be displayed.

・ Dusive ability: 12000 ・ Current: 4 to 20mA DC (maximum load resistance 550Ω) ・ Output accuracy: within ± 0.3%of transmission output 1 span

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ Control board embedded method (compatible panel thickness 1 ~ 8mm)
・ Case: flame -retardant resin color: black
・ Panel: Membrane sheet
・ Drip -proof / dustproof structure: front IP66

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W48XH96XD110mm case depth: 98.5mm (at panel mount)

Approximately 280g

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9600, 19200, 38400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

AER-102-Ech1, EVT3

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

Temperature: ± 1 ℃

Conductive zero adjustment coefficient setting range: See item in the measurement range

Calibration range: -10.0 ~ 10.0 ℃

・ Relay contact 1A
・ Control capacity: 3A 250V AC (resistance load), 1A 250V AC (induced load COSφ = 0.4)
・ Electrical life: 100,000 times
・ Control operation: P operation, ON/OFF operation

-Denstrual rate, temperature, and MV are converted to analog amount for each input sampling and output by current. (Factory shipping: Conductive)

・ If the transmission output 1 maximum value and transmission output 1 are set to the same value, the transmission output 1 is 4 ma DC fixed.
・ The transmission output volume can be displayed.

・ Dusive ability: 12000 ・ Current: 4 to 20mA DC (maximum load resistance 550Ω) ・ Output accuracy: within ± 0.3%of transmission output 1 span

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ Control board embedded method (compatible panel thickness 1 ~ 8mm)
・ Case: flame -retardant resin color: black
・ Panel: Membrane sheet
・ Drip -proof / dustproof structure: front IP66

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W48XH96XD110mm case depth: 98.5mm (at panel mount)

Approximately 280g

AER-102-Ech1, TA2

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

・ Conductive: ± 0.5% of measurement range span
・ Salt conversion: ± 1% of measured range span
・ TDS conversion: ± 1.5% of measurement range span

Temperature: ± 1 ℃

Conductive zero adjustment coefficient setting range: See item in the measurement range

Calibration range: -10.0 ~ 10.0 ℃

・ Relay contact 1A
・ Control capacity: 3A 250V AC (resistance load), 1A 250V AC (induced load COSφ = 0.4)
・ Electrical life: 100,000 times
・ Control operation: P operation, ON/OFF operation

-Denstrual rate, temperature, and MV are converted to analog amount for each input sampling and output by current. (Factory shipping: Conductive)

・ If the transmission output 1 maximum value and transmission output 1 are set to the same value, the transmission output 1 is 4 ma DC fixed.
・ The transmission output volume can be displayed.

・ Dusive ability: 12000 ・ Current: 4 to 20mA DC (maximum load resistance 550Ω) ・ Output accuracy: within ± 0.3%of transmission output 1 span

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ Control board embedded method (compatible panel thickness 1 ~ 8mm)
・ Case: flame -retardant resin color: black
・ Panel: Membrane sheet
・ Drip -proof / dustproof structure: front IP66

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W48XH96XD110mm case depth: 98.5mm (at panel mount)

Approximately 280g