Plug-in-type digital indicator derivative rate meter WIL-102-Ech (high concentration)
Shinko Technos Co., Ltd.

WIL-102-Ech, EVT

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Calonize the conductive rate zero adjustment and conductive rate span adjustment.
・ Conductive adjustment adjustment: zero adjustment coefficient setting range -10%of input span -10%of input span
・ Conductive span adjustment: Span adjustment coefficient range 0.700 ~ 1.300

When the sensor cannot be installed in the area you want to measure, the temperature measured by the sensor and the temperature of the measured site
The degree may be different. In such a case, the temperature school positive value can be set to match the temperature of the measurement point to the desired temperature.

Adjustment range: -10.0 ~ 10.0 ℃

TDS is an abbreviation of Total Dis Orved Solids, which means full -dissolved solid volume. The conductivity of the solution is due to the amount of salt, minerals, and the amount of dissolved gas.

The conductive rate is an index indicating all the substances in the solution, and the TDS indicates only the full -mixed amount of solids.

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9,600, 19,200, 38,400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

4 -pole conductive conductor sensor (temperature element: PT100), 4 -pole conductive rate sensor (temperature element: PT1000)

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

WIL-102-Ech, TA

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Calonize the conductive rate zero adjustment and conductive rate span adjustment.
・ Conductive adjustment adjustment: zero adjustment coefficient setting range -10%of input span -10%of input span
・ Conductive span adjustment: Span adjustment coefficient range 0.700 ~ 1.300

When the sensor cannot be installed in the area you want to measure, the temperature measured by the sensor and the temperature of the measured site
The degree may be different. In such a case, the temperature school positive value can be set to match the temperature of the measurement point to the desired temperature.

Adjustment range: -10.0 ~ 10.0 ℃

TDS is an abbreviation of Total Dis Orved Solids, which means full -dissolved solid volume. The conductivity of the solution is due to the amount of salt, minerals, and the amount of dissolved gas.

The conductive rate is an index indicating all the substances in the solution, and the TDS indicates only the full -mixed amount of solids.

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9,600, 19,200, 38,400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

4 -pole conductive conductor sensor (temperature element: PT100), 4 -pole conductive rate sensor (temperature element: PT1000)

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

WIL-102-Ech, TA2

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Calonize the conductive rate zero adjustment and conductive rate span adjustment.
・ Conductive adjustment adjustment: zero adjustment coefficient setting range -10%of input span -10%of input span
・ Conductive span adjustment: Span adjustment coefficient range 0.700 ~ 1.300

When the sensor cannot be installed in the area you want to measure, the temperature measured by the sensor and the temperature of the measured site
The degree may be different. In such a case, the temperature school positive value can be set to match the temperature of the measurement point to the desired temperature.

Adjustment range: -10.0 ~ 10.0 ℃

TDS is an abbreviation of Total Dis Orved Solids, which means full -dissolved solid volume. The conductivity of the solution is due to the amount of salt, minerals, and the amount of dissolved gas.

The conductive rate is an index indicating all the substances in the solution, and the TDS indicates only the full -mixed amount of solids.

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9,600, 19,200, 38,400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

4 -pole conductive conductor sensor (temperature element: PT100), 4 -pole conductive rate sensor (temperature element: PT1000)

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

WIL-102-Ech1, EVT

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Calonize the conductive rate zero adjustment and conductive rate span adjustment.
・ Conductive adjustment adjustment: zero adjustment coefficient setting range -10%of input span -10%of input span
・ Conductive span adjustment: Span adjustment coefficient range 0.700 ~ 1.300

When the sensor cannot be installed in the area you want to measure, the temperature measured by the sensor and the temperature of the measured site
The degree may be different. In such a case, the temperature school positive value can be set to match the temperature of the measurement point to the desired temperature.

Adjustment range: -10.0 ~ 10.0 ℃

TDS is an abbreviation of Total Dis Orved Solids, which means full -dissolved solid volume. The conductivity of the solution is due to the amount of salt, minerals, and the amount of dissolved gas.

The conductive rate is an index indicating all the substances in the solution, and the TDS indicates only the full -mixed amount of solids.

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9,600, 19,200, 38,400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

4 -pole conductive conductor sensor (temperature element: PT100), 4 -pole conductive rate sensor (temperature element: PT1000)

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

WIL-102-Ech1, TA

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Calonize the conductive rate zero adjustment and conductive rate span adjustment.
・ Conductive adjustment adjustment: zero adjustment coefficient setting range -10%of input span -10%of input span
・ Conductive span adjustment: Span adjustment coefficient range 0.700 ~ 1.300

When the sensor cannot be installed in the area you want to measure, the temperature measured by the sensor and the temperature of the measured site
The degree may be different. In such a case, the temperature school positive value can be set to match the temperature of the measurement point to the desired temperature.

Adjustment range: -10.0 ~ 10.0 ℃

TDS is an abbreviation of Total Dis Orved Solids, which means full -dissolved solid volume. The conductivity of the solution is due to the amount of salt, minerals, and the amount of dissolved gas.

The conductive rate is an index indicating all the substances in the solution, and the TDS indicates only the full -mixed amount of solids.

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9,600, 19,200, 38,400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

4 -pole conductive conductor sensor (temperature element: PT100), 4 -pole conductive rate sensor (temperature element: PT1000)

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

WIL-102-Ech1, TA2

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Conductive: ± 0.5% of input span
・ Salt conversion: ± 1% of input span
・ TDS conversion: ± 1.5% of input span

・ Calonize the conductive rate zero adjustment and conductive rate span adjustment.
・ Conductive adjustment adjustment: zero adjustment coefficient setting range -10%of input span -10%of input span
・ Conductive span adjustment: Span adjustment coefficient range 0.700 ~ 1.300

When the sensor cannot be installed in the area you want to measure, the temperature measured by the sensor and the temperature of the measured site
The degree may be different. In such a case, the temperature school positive value can be set to match the temperature of the measurement point to the desired temperature.

Adjustment range: -10.0 ~ 10.0 ℃

TDS is an abbreviation of Total Dis Orved Solids, which means full -dissolved solid volume. The conductivity of the solution is due to the amount of salt, minerals, and the amount of dissolved gas.

The conductive rate is an index indicating all the substances in the solution, and the TDS indicates only the full -mixed amount of solids.

Perform the following operations from the external computer.
・ Read and set various set values
・ Reading of the conductive rate, temperature, and state
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9,600, 19,200, 38,400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

4 -pole conductive conductor sensor (temperature element: PT100), 4 -pole conductive rate sensor (temperature element: PT1000)

0.0 to 100.0 ° C

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)