All Categories
History
15 products found
Kawatatek Co., Ltd.
570+ people viewing
Last viewed: 1 day ago
■ Characteristics ・ Large φ700 (28 ") ・ Direct mounting (JIS ・ ASA) short taper A type ・ It can be replaced with an integrated claw type ・ T j...
10 models listed
Kawatatek Co., Ltd.
850+ people viewing
Last viewed: 1 day ago
The inside of the main unit is suitable for heavy sharpening because the accuracy, balance, etc. are good due to special design. The body is a tren...
10 models listed
Kawatatek Co., Ltd.
5050+ people viewing
Last viewed: 1 hour ago
The jig mounting is a safety design of tap hole specifications. You can use the raw snail by replacing the standard one claws with the 46DJ series ...
10 models listed
Kawatatek Co., Ltd.
7350+ people viewing
Last viewed: 6 hours ago
It is a common chuck made of main body casting and has been used for a long time. The jig mounting can be used by replacing the safety design of ta...
9 models listed
Kawatatek Co., Ltd.
800+ people viewing
Last viewed: 3 hours ago
It is a plate attached to the scroll chuck. * There are other model numbers.
10 models listed
Kawatatek Co., Ltd.
710+ people viewing
Last viewed: 1 hour ago
There are a claws and a two -piece type. The top of the chuck is a T groove or tap specification. ■ Characteristics ・ Made of main body casting ...
6 models listed
Kawatatek Co., Ltd.
650+ people viewing
Last viewed: 18 hours ago
It has a built -in floating function for ring processing. The FLC type has a centrifugal correction function. ■ FLC series ・ Long jo -chirik 86mm...
7 models listed
Kawatatek Co., Ltd.
3740+ people viewing
Last viewed: 5 hours ago
■ Characteristics ・ Made of main body casting (for normal cutting) ・ Chuck size 5 "to 24" (φ132 -φ610) ・ After attaching to the back plate, atta...
10 models listed
Kawatatek Co., Ltd.
1730+ people viewing
Last viewed: 7 minutes ago
Since it is grasped with 5 claws, there is little deformation of the processing material, and the hole diameter is large, so it is suitable for pip...
8 models listed
Kawatatek Co., Ltd.
780+ people viewing
Last viewed: 2 hours ago
■ Characteristics ・ Made of main body casting (for normal cutting) ・ Chuck size 3 ~ 12 ”(φ87 -φ310) ・ After mounting to the back plate, attach ...
8 models listed
Kawatatek Co., Ltd.
2060+ people viewing
Last viewed: 3 hours ago
■ Characteristics ・ Chuck size 21 "to 71" (φ535 ~ φ1,800) ・ Up to φ710 outer diameter is made of the main body steel, and φ800 or more is made of...
10 models listed
Kawatatek Co., Ltd.
840+ people viewing
Last viewed: 4 hours ago
■ Characteristics ・ Made of main body casting (for normal cutting) ・ Chuck size 6 "to 8" (φ165 -φ460) ・ Dust mounted on the lathe main axis (JIS...
10 models listed
Kawatatek Co., Ltd.
1440+ people viewing
Last viewed: 8 hours ago
You can grasp the square (square) work and cylindrical work. You can also grasp the work of a rectangle by forming a raw claw. ■ Characteristics ...
9 models listed
Kawatatek Co., Ltd.
1260+ people viewing
Last viewed: 4 hours ago
You can grasp the pipe -shaped work with less hizzle. ■ Characteristics ・ Made of main body casting (for normal cutting) ・ Chuck size 9 "to 12" ...
5 models listed
Kawatatek Co., Ltd.
1660+ people viewing
Last viewed: 1 hour ago
This is a chuck used by attaching it to a table of the Ichele, a machineing center, and a 5 -axis processor table. Lightweight and thin, so it is l...
6 models listed