Shimatec Co., Ltd.'s Feeders

Types ST-1 to ST-4 are full-wave drive. The ST-5 type is available in both full-wave drive and half-wave drive. The ST-6 type is half-wave drive.

• FA Equipment

• Feeders

Vibration adjustment is easy and runs smoothly.Both the front and rear spring angles can be changed, allowing fine adjustment of the workpiece run....

• FA Equipment

• Feeders

Compatible with faster production lines and inspection machines. Shinko Electric's Dialmotion parts feeder enables high-speed supply of screws, bol...

• FA Equipment

• Feeders

Please don't buy a parts feeder again. Do you know how many years ago parts feeders were invented? It was invented in 1940 by William V. Spurlin of...

• FA Equipment

• Feeders

■Features ・Maintenance free ・Easy to dispose of garbage - Strong against impact and load Guide rails and attachments can be attached to the oute...

• FA Equipment

• Feeders

We supply all kinds of food ingredients hygienically and quickly. Rotary feeder that is not a vibratory parts feeder ■Features ・The entire device...

• FA Equipment

• Feeders

There is a method that does not use a parts feeder to feed pins, steel balls, hexagonal shafts, pipes, bushes, etc. ■Features of parts feeder for ...

• FA Equipment

• Feeders

Pins, balls, pipes, hexagonal materials, etc. that are piled up loosely in the hopper are pulled out in a single row. Product development line tech...

• FA Equipment

• Feeders

Pin feeder for steel balls

• FA Equipment

• Feeders

• FA Equipment

• Feeders

The workpieces stacked in bulk in the hopper are removed. ■Features ・It's quiet. ・No damage to the workpiece. - Simple structure and no failures...

• FA Equipment

• Feeders

4-row supply/escape and pressure feeding functions included

• FA Equipment

• Feeders

3-row supply / common use for many types of workpieces

• FA Equipment

• Feeders

Parts feeder parallel arrangement/line feeder 2 rows

• FA Equipment

• Feeders

8 row escape device

• FA Equipment

• Feeders

Sorting out short defective pins in the parts feeder

• FA Equipment

• Feeders

Common use of thin workpieces of 0.1t×φ2.5, φ3, and φ3.5. Supply/escape with parts feeder

• FA Equipment

• Feeders

Mechanical sorting of workpiece shapes that cannot be sorted by parts feeder

• FA Equipment

• Feeders

By installing this equipment on the rice cooker production line, productivity is dramatically improved.

• FA Equipment

• Feeders

Escape Escape Difficult Work

• FA Equipment

• Feeders

Parts feeder with hardening treatment (tuftride)

• FA Equipment

• Feeders

Parts feeder for heavy workpieces with φ1,000 stages

• FA Equipment

• Feeders

Automatic measurement and defect selection of workpiece weight using electronic tsubo

• FA Equipment

• Feeders

Simple thickness inspection device. A fiber sensor is used for thickness inspection.

• FA Equipment

• Feeders

Inspects for the presence of threads and discharges defective products to the outside of the parts feeder. With 100L hopper

• FA Equipment

• Feeders

Measure and inspect three sides of a rectangular chip. Each location (3 surfaces) is inspected 40 times for 0.4 seconds every 0.01 seconds.The insp...

• FA Equipment

• Feeders

Inspect the head of the workpiece with a camera to determine defective products

• FA Equipment

• Feeders

Uses a high-precision proximity sensor (setting resolution 0.5μm). Inspection tact approximately 1 second. Master measurement, reset any position o...

• FA Equipment

• Feeders

Auto parts. Thickness, inner diameter, and plating defect inspection device.

• FA Equipment

• Feeders

Press fit the resin part into the M-shaped fitting. Commonly used with other varieties. We count the number of products produced, and after quantit...

• FA Equipment

• Feeders

Bicycle parts. Stamping machine. Engrave a burr on the workpiece to prevent rotation.

• FA Equipment

• Feeders

Special screws for mobile phones, screw head cross cutter machine. Cut the head of the screw crosswise.

• FA Equipment

• Feeders

Architectural anchor and nail cutter machine. Make a notch in the nail.

• FA Equipment

• Feeders

Drills holes in two workpieces at the same time. Drill holes from both sides of the workpiece to avoid burrs.

• FA Equipment

• Feeders

Automatic loom parts, wire processing machines. Process the pin-shaped wire into a spiral.

• FA Equipment

• Feeders

Architectural floor support, 4-axis screw tightening machine. After tightening the screws on the 4 axes, rotate 45 degrees and tighten the screws i...

• FA Equipment

• Feeders

After spot welding, we inspect the product, count the number of products produced, and pack the work into a fixed number of boxes.

• FA Equipment

• Feeders

Architectural anchor parts, nail spot welding machine. Spot weld the half-split nail and insert the washer.

• FA Equipment

• Feeders

The workpiece is fed to the parts feeder using a belt with a sunshade.

• FA Equipment

• Feeders

The workpiece is transported by a belt with a sunshade, and the horizontal conveyor section secures the foot roll.

• FA Equipment

• Feeders

Stock a certain amount of workpieces in the bucket and feed them to the parts feeder.

• FA Equipment

• Feeders

Feeds long workpieces horizontally one by one (patent pending)

• FA Equipment

• Feeders

■Features ・Full surface SUS specification ・Full surface welding・No pinholes・Electrolytic polishing・Buffing ・One-touch attachment and detachme...

• FA Equipment

• Feeders

• FA Equipment

• Feeders

• FA Equipment

• Feeders

The glass tube and the metal parts on both ends are glued together and dried on a conveyor.

• FA Equipment

• Feeders

Automatic loom parts. Lapet assembly type. Assemble 3 types of workpieces.

• FA Equipment

• Feeders