Excellent elasticity withdrawal to prevent withdrawal SKX
Kawa Nishi Water Waterway Equipment Co., Ltd.
About This Product
SKX is excellent in elasticity, absorbs tube distortion and demonstrates high earthquake -resistant performance. It is also characterized by the highly erosion of carbon content of 3.6%to 4.0%special FCV cast iron. It is possible to join without the need to be decomposed, and the hands tightening and tightening are dramatically improved than the conventional products.
■ Tolerant water pressure: 1MPa
・ Tolerant water pressure = maximum water pressure+water pressure
・ Please contact us when using 1MPa or higher.
・ The allowable water pressure in polyethylene tubes is 0.75 MPa
■ Temperature used
・ Up to 45 ° C for common hot water.
・ Up to 60 ° C for short term.
■ Basic standard certification
・ Certificate registration number: G-270
・ Authentication organization: (Public Corporation) Japan Water supply Association Quality Authorization Center
・ For water supply
・ Performance item: 1. Poltolic resistance 2. Deepment * There are also non -authentication registration products.
■ SKX rubber packing structure
Developed an inner convex shape packing. By combining with the Teflon Film Washer, the structure is unnecessarily adhered to the tube with a small force without a slimming agent, and it supports all tube types.
■ SKX stop ring
・ 10-50mm stopping appears in the entire diameter.
・ For 25mm or less, it is possible to apply for both PVC tubes and steel pipes by W -ring stopping development and restore the restoration.
-The stopping and C conjunction are independent, and the entotence of 7 mm or more is achieved in the entire diameter, and a horn of ± 3 ° or more is realized.
■ Inner and outer epoxy resin powder paint
・ Pin hole is less likely to occur during painting due to a special base treatment, and the coating is good.
・ Inner surface: The minimum membrane thickness 0.2mm or more
・ External surface: target average membrane thickness 0.1mm or more
・ Thin screw part
■ Significant workability
・ It can be joined without disassembling and slides on the joint pipe without resistance.
-The construction of hands and tightening is dramatically improved than conventional products.
・ No pipe pre -treatment (chamfer, polishing, oil removal, insertion of in ring) is required.
・ After tightening the cap, tighten the stop ring, so there is no tube.
■ No big pipe wrench required
・ Cap tightening power has been greatly reduced by independent watertight function and tube holding function.
・ The construction time is reduced by using a short wrench.
■ Heading construction, restoration, and rebuilding is possible
・ Polyethylene tubes, PVC tubes, and steel pipes can be tightened all sizes.
-The stopping is open by adopting a W -ring structure or less by loosening the bolt nut.
■ Others
Achieving low torque tightening and co -circular prevention
* There are other model numbers.
-
Product
Excellent elasticity withdrawal to prevent withdrawal SKX
-
Handling Company
Kawa Nishi Water Waterway Equipment Co., Ltd.
-
Categories
10 Models of Excellent elasticity withdrawal to prevent withdrawal SKX
Items marked with have different values depending on the model number.
Click on the part number for more information about each product
| Product Image | Part Number | Price (excluding tax) | 1 hour later (reference) | Destruction water pressure | Expansion and contraction | Hypopuspension | Internal pressure | Negative pressure | Nominal diameter | Potential | Pressure -bearing | Pull -out test | Pulling preventive force (water pressure conversion) | SKX Nominal Diameter (SR) | SKX nominal diameter (body) | Vibration test | Water pressure | Withdrawal power |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
1st kind of general |
Available upon quote | 4.7 | - | - | 0.02MPa (2 minutes) | - | - | Ten | - | - | 0.46kn (1h) | - | P10 gray | V13 | - | 1.75MPa (1h) | - |
|
|
Two types of general |
Available upon quote | 3.3 | - | - | 0.02MPa (2 minutes) | - | - | Ten | - | - | 0.94kn (1h) | - | P10 gray | V13 | - | 1.75MPa (1h) | - |
|
|
Water supply polyethylene tube (P) |
Available upon quote | 3.95 ~ 4.85 % | Destroyed water pressure or higher | - | 0.02MPa (2 minutes) | - | -54kpa (2 minutes) | 13 ~ 50 | - | - | 0.97 ~ 6.40KN (1h) | - | P13 ~ P50 gray | 16 ~ 50 | - | 1.75MPa (1h) | - |
|
|
High density polyethylene tube JIS outer diameter (P) |
Available upon quote | 4.10 to 5.80 % | - | - | 0.02MPa (2 minutes) | - | -54kpa (2 minutes) | 20 ~ 50 | - | - | 2.72 ~ 10.17KN (1h) | - | P20 ~ P50 gray | 20 ~ 50 | - | 1.75MPa (1h) | - |
|
|
High density polyethylene tube ISO outer diameter (ISO-P) |
Available upon quote | 4.05 ~ 5.20 % | Destroyed water pressure or higher | - | 0.02MPa (2 minutes) | - | -54kpa (2 minutes) | 20 ~ 50 | - | - | 2.95 ~ 11.3kn (1h) | - | ISO-P25 ~ ISO-P50 Sora color | 25 ~ D50 | - | 1.75MPa (1h) | - |
|
|
PVC pipe for water (V) |
Available upon quote | - | - | 7mm or more | - | 0⇔2MPa 1,500 cycle (6.5 seconds) | -54kpa (2 minutes) | 13 ~ 50 | ± 3 ° or more | 4MPa (1 minute) | - | - | V13 ~ V50 Navy | V13 ~ 50 | - | - | 2.0 ~ 11.3kn (4 ~ 8MPa) |
|
|
Steel pipe for water pipe (SGP) |
Available upon quote | - | - | 7mm or more | - | 0⇔2MPa 1,500 cycle (6.5 seconds) | -54kpa (2 minutes) | 15A ~ 50A | ± 3 ° or more | 4MPa (1 minute) | - | - | 16 ~ 50 Black | 16 ~ 50 | - | - | 3.7 ~ 17.2kn (6-10MPA) |
|
|
Stainless steel pipe for general piping (SU) |
Available upon quote | - | - | 7mm or more | - | 0⇔4MPa 1,500 cycle (6.5 seconds) | -54kpa (2 minutes) | 20SU ~ 50SU | ± 2.2 ° or more | 4MPa (1 minute) | - | 3.4 ~ 9.2kn (5.0 ~ 8.8MPa) | Su20 ~ su50 white | 16 ~ 40 | 1.75MPa ± 2.2 ° or more 120 times/minutes 20,000 times | - | - |
|
|
Stainless steel pipe for piping (SUS) |
Available upon quote | - | - | 7mm or more | - | 0⇔2MPa 1,500 cycle (6.5 seconds) | -54kpa (2 minutes) | 15A ~ 50A | ± 3 ° or more | 4MPa (1 minute) | - | - | 16 ~ 50 Black | 16 ~ 50 |
1.75MPa 120 times/minutes 20,000 times ・ (15A to 25A) Vibration ± 2.2 ° ・ (32a ~ 50A) Vibration ± 1.5 ° |
- | 3.7 ~ 14.4kn (5.0 ~ 9.2MPa) |
|
|
VD steel pipe (VD) |
Available upon quote | - | - | 7mm or more | - | - | -54kpa (2 minutes) | 15A ~ 50A | ± 3 ° or more | 4MPa (1 minute) | - | - | D15 ~ D50 red | 20 ~ D50 | - | - | 5.2 ~ 19.1kn (6-10MPA) |
Click on the part number for more information about each product
Customers who viewed this product also viewed
Other products of Kawa Nishi Water Waterway Equipment Co., Ltd.
View more products of Kawa Nishi Water Waterway Equipment Co., Ltd.
