Plug-in-type digital instruction turbidity/SS meter WIL-101-TU
Shinko Technos Co., Ltd.

WIL-101-TU, EVT

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

500ms

Within ± 1%for the set time

1 to 120 times

Perform the following operations from the external computer.・ Reading and setting of various set values/setting/turbidity/SS input value, state reading/function change, adjustment/user preservation area reading and setting

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9600, 19200, 38400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

Circular degree detection device (Optex Co., Ltd. Muddy degree checker) TC-100, TC-500, TC-3000

SS detector (SS checker manufactured by Optex Co., Ltd.) TCS-1000 (E), TS-MXS-A

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

As a contact output, select by key operation from among the following, no operation, no turbidity/SS input lower limit operation, turbidity/SS input upper limit, ERR output, Fail output, turbidity, ss input upper and lower operations separately separately.

・ Relay contact 1A (In serial communication, there is a bit information in 4 flags per output) ・ Contact output: 1 point

WIL-101-Tu, TA

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

500ms

Within ± 1%for the set time

1 to 120 times

Perform the following operations from the external computer.
・ Read and set various set values
・ Calculation/SS input value, state reading
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9600, 19200, 38400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

Circular degree detection device (Optex Co., Ltd. Muddy degree checker) TC-100, TC-500, TC-3000

SS detector (SS checker manufactured by Optex Co., Ltd.) TCS-1000 (E), TS-MXS-A

0 to 50 ℃

35 ~ 85%RH (but not condensation)

100 ~ 240 V AC 50/60 Hz tolerance fluctuation range: 85 ~ 264 v AC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

As a contact output, select by key operation from the following
・ No movement
・ Muddyness/SS input limit operation
・ Muddyness/SS input upper limited operation
・ ERR output
・ Fail output
・ Muddy degree/SS input input upper and lower limited operation

・ Relay contact 1A (with a bit information in 4 state flags per output in serial communication)
・ Contact output: 1 point

WIL-101-TU1, EVT

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

500ms

Within ± 1%for the set time

1 to 120 times

Perform the following operations from the external computer.
・ Read and set various set values
・ Calculation/SS input value, state reading
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9600, 19200, 38400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

Circular degree detection device (Optex Co., Ltd. Muddy degree checker) TC-100, TC-500, TC-3000

SS detector (SS checker manufactured by Optex Co., Ltd.) TCS-1000 (E), TS-MXS-A

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

As a contact output, select by key operation from the following
・ No movement
・ Muddyness/SS input limit operation
・ Muddyness/SS input upper limited operation
・ ERR output
・ Fail output
・ Muddy degree/SS input input upper and lower limited operation

・ Relay contact 1A (with a bit information in 4 state flags per output in serial communication)
・ Contact output: 1 point

WIL-101-TU1, TA

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

± 0.2%± 1 digit of the measurement range span (however, no sensor accuracy is included)

500ms

Within ± 1%for the set time

1 to 120 times

Perform the following operations from the external computer.
・ Read and set various set values
・ Calculation/SS input value, state reading
・ Change and adjust function
・ Reading and setting of user storage area

1.2 km (maximum) Cable resistance within 50Ω (end resistance: None or 120Ω or more on both sides)

EIA RS-485 compliant

Half double communication

Select 9600, 19200, 38400 BPS by key operation

Toning synchronization

ASCII, binary

Select Shinko Standard, Modbus ASCII, Modbus RTU by key operation

8 bits/none, 7 -bit/none, 8 -bit/even number, 7 -bit/even number, 8 -bit/odd, 7 -bit/odd number by key operation

Select 1 bit and 2 bits by key operation

Command resend

・ Parity check, checksum (Shinko standard)
・ LRC (Modbus ASCII), CRC-16 (Modbus RTU)

Motor the CPU with a watchdog timer and make the instrument into an initial state in the event of an abnormality.

Circular degree detection device (Optex Co., Ltd. Muddy degree checker) TC-100, TC-500, TC-3000

SS detector (SS checker manufactured by Optex Co., Ltd.) TCS-1000 (E), TS-MXS-A

0 to 50 ℃

35 ~ 85%RH (but not condensation)

24 V AC/DC 50/60 Hz Available range range: 20-28 v AC/DC

・ DIN rail mounting method
・ Case: flame -retardant resin color: Light gray
・ Panel: Membrane sheet

Over-pressure category Ⅱ, pollution 2 (IEC61010-1)

ROHS command support

W30XH88XD108mm (including socket)

Approximately 200g (including socket)

As a contact output, select by key operation from the following
・ No movement
・ Muddyness/SS input limit operation
・ Muddyness/SS input upper limited operation
・ ERR output
・ Fail output
・ Muddy degree/SS input input upper and lower limited operation

・ Relay contact 1A (with a bit information in 4 state flags per output in serial communication)
・ Contact output: 1 point