All Categories

History

[Non-contact] Light beam touch sensor invisible installation type HA-T401-HA-T401
[Non-contact] Light beam touch sensor invisible installation type HA-T401-Hotron Co., Ltd.

[Non-contact] Light beam touch sensor invisible installation type HA-T401
Hotron Co., Ltd.

Hotron Co., Ltd.'s Response Status

Response Rate

100.0%

Response Time

45.3hours


About This Product

Automatic door sensors open only those who want to enter without contact, even on busy roads or narrow aisles. A non-contact touch sensor that can be used to save energy and prevent infectious diseases.

■Four spot settings to suit various door types

There are also types of automatic doors that open on one side and types that open on both sides. The HA-T401 can be set to four different detection range rows: left, center, right, 4 spots, and 12 spots, depending on the environment in which it is installed.

■Recommended for these places

Case 1: Door facing a narrow passage The staff room was right next to the automatic door, and every time I passed by, the door was open. Using a non-contact optical touch sensor eliminates unnecessary opening and closing. Case 2: There is a counter near the door The optical touch sensor HA-T401 has a narrow detection range, so even if there is a counter near the door, it will not interfere and can be opened and closed smoothly.

■Clear hygiene issues without contact

Nowadays, people are concerned about preventing infectious diseases, and there have been cases where touch switches have been installed at sites facing narrow aisles, where hygiene is a concern because an unspecified number of people come into contact with them. With the optical touch sensor, you can open and close the automatic door just by approaching the door without touching it, which is safe from a sanitary perspective.

■Two setting modes that reduce unnecessary door opening and closing and contribute to energy savings

You can open and close the automatic door by selecting from two patterns the conditions for detecting a passerby and opening the door.

■Can also be used as a blind infrared sensor

When the light beam touch function is turned off, it can also be used as an invisible infrared sensor with a wide detection range. ON/OFF of the light beam touch function can be confirmed by the color of the LED during standby.

■No need to replace battery of switch

By replacing the conventional touch switch (battery-operated) with a touch seal, batteries are no longer required, saving you the trouble of replacing batteries.

  • Product

    [Non-contact] Light beam touch sensor invisible installation type HA-T401

Share this product


160+ people viewing

Last viewed: 15 hours ago


Free
Get started with our free quotation service - no cost, no obligation.

No Phone Required
We respect your privacy. You can receive quotes without sharing your phone number.

1 Models of [Non-contact] Light beam touch sensor invisible installation type HA-T401

Image Part Number Price (excluding tax) Stationary object detection time Power supply Snow level Mass Insect mode Self-diagnosis function Power consumption/current Detection method Sensitivity adjustment function Response time Interference prevention Width range setting Depth range setting Mounting height Mounting part distortion countermeasures Output contact Output holding time Ray touch range setting Operating temperature range Cover color Eco mode 1st row setting Accessories
[Non-contact] Light beam touch sensor invisible installation type HA-T401-Part Number-HA-T401

HA-T401

Available upon quote

Starting range (outer 2 rows): 2 seconds/10 seconds (dip switch setting)
Existence range (3 rows on the door side): 2 seconds / 10 seconds / 60 seconds / ∞ seconds (dip switch setting)

AC/DC12 ~ 110V±10% 50/60Hz

Level 0 (none) /1/2/3 (dip switch setting)

Approximately 290g

Yes/No (Dip switch setting)

Yes/No (Dip switch setting)

At AC100V: 4.3VA or less At AC24V: 2.5VA or less At AC12V: 2.5VA or less
At 24V DC: 65mA or less At 12V DC: 140mA or less

Near-infrared reflection method

Yes (sensitivity volume setting)

Approximately 0.1 seconds *May be approximately 0.2 seconds depending on settings

6 frequency settings (dip switch settings)

Detection width setting: 6 to 2 rows (dip switch settings for left and right)
Detection range movement: 1 row movement (width range adjustment knob setting for left and right)

Angle adjustment: Main body 0 ~ +15° (depth range adjustment screw)
Detection column setting: 5 ~ 2 columns (dip switch setting)

2.0 ~ 4.0m (up to 3.0m when used as a light beam touch sensor)

Yes/No (dip switch setting) (for cases other than light beam touch)

Output 1 (start) - No-voltage relay contact 1a (when detected: make) DC50V 0.1A (resistive load)
Output 2 (auxiliary) - Non-current contact (MOS relay) 1a (when detected: make) DC50V 0.1A (resistive load)

Approximately 0.5 seconds

Center/Left/Right/All (Center+Left+Right)
Disable selection other than light beam touch (dip switch setting)

-20 ~ +60℃ (no condensation)

S: Silver, B: Bronze, W: White, M: Mirror, K: Black, G: Stainless steel color

Yes/No (dip switch setting) (for cases other than light beam touch)

Doorway monitoring automatic/doorway monitoring forced/light touch/normal (dip switch setting)

Wiring code 4P (2m), mounting screws (2 pcs), wiring code 2P (2m), installation pattern, light touch installation manual, instruction manual

Customers who viewed this product also viewed

Reviews shown here are reviews of companies.

See More Touch Sensors Products

Other products of Hotron Co., Ltd.

Reviews shown here are reviews of companies.


View more products of Hotron Co., Ltd.

About Company Handling This Product

Response Rate

100.0%


Response Time

45.3hrs

  • Japan

This is the version of our website addressed to speakers of English in the United States. If you are a resident of another country, please select the appropriate version of Metoree for your country in the drop-down menu.

Copyright © 2024 Metoree