All Categories

History

Relay terminal block for sequencer Analog input/output unit Screw terminal type For isolated analog unit (small type) FA1-TBS40DAG-FA1-TBS40DAG
Relay terminal block for sequencer Analog input/output unit Screw terminal type For isolated analog unit (small type) FA1-TBS40DAG-Mitsubishi Electric Engineering Co., Ltd.

Relay terminal block for sequencer Analog input/output unit Screw terminal type For isolated analog unit (small type) FA1-TBS40DAG
Mitsubishi Electric Engineering Co., Ltd.


About This Product

■Product overview

Relay terminal blocks are products that relay signals between control equipment (sequencers) and devices (sensors, etc.) using a connection method tailored to the application.

■Features 1.

The use of a screw fall prevention mechanism prevents screws from falling off, and the use of a screw retention mechanism makes it easy to install round crimp terminals.

■Features 2.

The terminal screws are black for every 5 terminals, making it easy to confirm the terminal position.

■Feature 3.

Can be mounted by DIN rail or screws.

■Notes

・*1: Do not use or store in an environment pressurized above atmospheric pressure at an altitude of 0m. If used, it may malfunction. ・*2: Indicates which power distribution section, from the public power distribution network to on-premises machinery, the device is expected to be connected to. Category II applies to equipment that is powered from fixed equipment. The surge withstand voltage for devices rated up to 300V is 2,500V. ・*3: An index that indicates the degree of occurrence of conductive substances in the environment in which the device is used. Pollution degree 2 produces only non-conductive pollution. However, it is an environment where temporary conductivity can occur due to accidental condensation. ・If you do not push the unit connector until the connector locks, it may cause a contact failure. - When connecting R60DA8/16-G, please replace the terminal block symbol paper with the included symbol paper.

  • Product

    Relay terminal block for sequencer Analog input/output unit Screw terminal type For isolated analog unit (small type) FA1-TBS40DAG

Share this product


10+ people viewing

Last viewed: 26 minutes ago


Free
Get started with our free quotation service - no cost, no obligation.

No Phone Required
We respect your privacy. You can receive quotes without sharing your phone number.

1 Models of Relay terminal block for sequencer Analog input/output unit Screw terminal type For isolated analog unit (small type) FA1-TBS40DAG

Image Part Number Price (excluding tax) Overvoltage category *2 Unit installation (DIN rail) Unit installation (screws) Operating ambient temperature Ambient humidity Usage altitude *1 Usage atmosphere Storage ambient temperature Storage ambient humidity Connected equipment Connected device series Pollution level *3 Purpose Terminal block type Terminal block: terminal screw Terminal block: Applicable wire, tightening torque Deadline Dielectric strength voltage, insulation resistance Vibration resistance (if there is intermittent vibration) 5-8.4Hz Vibration resistance (if there is intermittent vibration) 8.4~150Hz Vibration resistance (if there is intermittent vibration) Number of sweeps Vibration resistance (when there is continuous vibration) 5-8.4Hz Vibration resistance (when there is continuous vibration) 8.4~150Hz Shockproof Product classification Installation location Mass (g)
Relay terminal block for sequencer Analog input/output unit Screw terminal type For isolated analog unit (small type) FA1-TBS40DAG-Part Number-FA1-TBS40DAG

FA1-TBS40DAG

$ 35.04〜

II or below

Compatible DIN rail: TH35-7.5Fe, TH35-7.5AL (based on JIS C 2812)

M4×0.7mm×25mm or more Tightening torque: 78~118N・cm (8~12kgf-cm)

0~55℃

5~95%RH (no condensation)

2,000m or less

No corrosive gas

-25~75℃

5~95%RH (no condensation)

Sequencer

MELSEC iQ-R, MELSEC-Q

2 or less

Wiring-saving/man-hour saving equipment

Screw terminal type

M3 screw, number of terminals: 40P, 7mm pitch, with screw retention and fall prevention mechanism

0.3~1.25mm^2 (when using crimp terminals), 43~58N・cm (4.4~5.9kgf-cm)

〇 (prepared product)

Between CHs: 1,000V AC for 1 minute, 10MΩ or more; Others: 500V AC for 1 minute, 10MΩ or more

Single amplitude 3.5mm

Acceleration 9.8m/s^2

10 times each in X, Y, and Z directions

Single amplitude 1.75mm

Acceleration 4.9m/s^2

147m/s^2, 3 times each in X, Y, and Z directions (JIS B 3502, IEC61131-2 compliant)

Relay terminal block for sequencer

Inside the control panel

Approximately 190

Customers who viewed this product also viewed

Reviews shown here are reviews of companies.

See More Terminal Blocks Products

Other products of Mitsubishi Electric Engineering Co., Ltd.

Reviews shown here are reviews of companies.


View more products of Mitsubishi Electric Engineering Co., Ltd.

About Company Handling This Product

This is the version of our website addressed to speakers of English in the United States. If you are a resident of another country, please select the appropriate version of Metoree for your country in the drop-down menu.

Copyright © 2025 Metoree