Integrated wire variant line
Tokyo Taira Line

■ Please try an ultra -fine variant line for small and lighter weight. We use high -precision rolling rolls to manufacture an ultra -fine variant line. Thick: Width = 1: 1 square line to 1: 2.5 flat line (minimum 0.1 x 0.1 to 0.1 x 0.25). In addition, ± 5 μm (± 0.005mm) has been achieved for dimension accuracy. For those with high precision requests, we also provide dice. I am also good at non -ferrous metals such as aluminum, copper, brass (brass), and Rin bronze. Most of the purpose of using an ultra -fine variant line is small and lighter in products, and the demand for ultra -fine variant wires is increasing as the world moves to a frivolous and short and small. Springs wrapped in square wires are more powerful than the spring with a round line of the same size, so it is often used in small equipment with only small space. In addition, regarding "kakuri wires", it can be wrapped in the same way without gaps, so you can flow large current even at the same size. Therefore, it is often used for small motors and transformers (transformers) wind lines. In the field of medical use, it is necessary to put a few thinner tubes (guide wires) than the endoscope to pass through an endoscope. Of course, the tube needs to bend freely, so a stainless steel spring is usually used. The ultra -fine variant is used for the purpose of compact copper wires for "heat dissipation pole of electronic components" and copper wires for "connector parts" that are difficult to get out of surface friction. In addition, we are constantly studying whether the 1mm to 16mm variants cannot be manufactured in a simpler way. The price of the variant line varies greatly depending on the manufacturing method. ■ Materials Currently, the materials we are handling are as follows. In addition, regarding iron rays and hard steel wires, you can adjust the hardness by yourself. 1. Iron wire ･ Normal iron wire (SWRM6, SWRM8, SWRM10) ･ Nashimi Line (SWM-A) ･ Carbon steel wire for cold pressure (SWCH12A, SWCH10R) ･ Zinc plated iron (SWMGS-3, SWMGS-1) ･ Zinc aluminum plating iron wire 2. Steel wire ･ SWRH62A, SW-A, SW-B, SW-C 3. Piano wire ･ SWP-A, SWP-B Four. Stainless steel line ･ SUS304-WPB, SUS304-1 / 2H, SUS304-W1 Five. Aluminum wire ･ A1070, A1050, A5052, A5056, A6063 6. Rin Floring Copper Line C5191 -H 7. Brass line C2600-3 / 4h, C2700 8. Copper wire C1100 (tough pitch same), C1020 (oxygen -free) 9. Special steel SNCM220 Ten. Western white Other materials are also possible. ■ Dimension standard (size) It is possible to process φ0.1 mm to φ12.0 mm with the material diameter. (The width of the flat line is up to 16 mm) Especially, we are focusing on 0.1 to 3.0mm fine variants. ■ Product loading and weight ･ Conventional roll → 1.5kg, 2kg, 3kg, 10kg, 50kg, 100kg (2kg, 10kg is a plastic bobbin roll) * You can also roll a 100kg to 200kg bobbin winding. Please consult us. ･ Coil roll → 30-100kg (inner diameter 8, 12, 16, 24 inches) ･ Carrier roll → 300-1000kg (Inner diameter 24, 26 inches) ･ Straight line cut → Length: about 1mm to 5500mm * In addition to the above square lines and flat lines, we will consult with various cross -sectional shapes and sizes.