All Categories

History

Tensile compression tester TG series-Sanyu Electronics Industry Co., Ltd.

Price (excluding tax)

Estimate Required

Sanyu Electronics Industry Co., Ltd.'s Response Status

Response Rate

100.0%

Response Time

72.4hours


Model Filter

You can search for other models from each index. The displayed value is the value of the currently selected part number.

Allowable test force for speed range

Analog output

Auto zero/auto calibration function

Cycle test function included as standard

Exam space

Load cell capacity determination function

Maximum test force

Measurement accuracy

Measuring range

Moving crosshead position display

Moving crosshead position display Maximum/minimum value setting

Moving crosshead speed range Return speed

Moving crosshead speed range Test speed

Moving crosshead stroke

Peak hold function

Safety device Emergency stop switch

Safety device Limit switch for overstroke prevention

Safety device Overload prevention

Safety device Servo amplifier abnormal stop

Setting maximum and minimum values

Speed ​​accuracy Optional test speed

Speed ​​accuracy Return speed

Speed ​​accuracy Test speed

Speed ​​range of moving crosshead Optional test speed

Speed ​​setting method Optional test speed

Speed ​​setting method Return speed

Speed ​​setting method Test speed

Test effective width

Test force display

Unit of measurement

See all 9 models in list
  • Part Number

    TG-1KN

Share this product


610+ people viewing

Last viewed: 7 minutes ago


Free
Get started with our free quotation service - no cost, no obligation.

No Phone Required
We respect your privacy. You can receive quotes without sharing your phone number.

Tensile compression tester TG series TG-1KN's performance table

Image Price (excluding tax) Allowable test force for speed range Analog output Auto zero/auto calibration function Cycle test function included as standard Exam space Load cell capacity determination function Maximum test force Measurement accuracy Measuring range Moving crosshead position display Moving crosshead position display Maximum/minimum value setting Moving crosshead speed range Return speed Moving crosshead speed range Test speed Moving crosshead stroke Peak hold function Safety device Emergency stop switch Safety device Limit switch for overstroke prevention Safety device Overload prevention Safety device Servo amplifier abnormal stop Setting maximum and minimum values Speed ​​accuracy Optional test speed Speed ​​accuracy Return speed Speed ​​accuracy Test speed Speed ​​range of moving crosshead Optional test speed Speed ​​setting method Optional test speed Speed ​​setting method Return speed Speed ​​setting method Test speed Test effective width Test force display Unit of measurement
Tensile compression tester TG series-Part Number-TG-1KN Available upon quote 1kN (102.0kgf) over the entire speed range DC0V~DC5V (Output connector: BNC) Standard accessory: Automatically performs zero point adjustment and span adjustment using the AUTO ZERO key when a load cell is connected. Cycle tests based on position values, cycles based on test force values, and combinations thereof are possible. Maximum number of repetitions: 9,999 times, maximum repetition rate: 5 times/min Tensile and compression tests can be performed at the bottom of the moving crosshead. Separately sold: Tensile test at the top and compression test at the bottom Standard accessories 1kN (102.0kgf) In the range of 20 to 100% of each range, □±1% of indicated value □±0.5% of indicated value 7 stages of 1,2,5,10,20,50,100 times (for 3mV/V load cell) 6-digit digital display (-signed) Minimum unit: 0.01mm, maximum display: 1,999.99mm Zero reset can be done at any position. Digital display settings using function keys Set either preset 1 speed or test speed With overshootless function 18 stages of 0.05, 0.1, 0.2, 0.3, 0.5, 1, 2, 3, 5, 10, 20, 30, 50, 100, 200, 300, 500, 1,000mm/min 760mm without test jig and load cell installed Standard accessory: Automatic peak reset at test start During operation, the drive power is cut off. It can be set to any position above or below the movement range of the moving crosshead. During operation, the drive power is cut off. When the test force value reaches 102% of the full scale of each range, a stop signal is output and the moving crosshead is stopped. During operation, the drive power is cut off. During operation, it outputs an operation stop signal and stops the moving crosshead. The above safety devices will display an alarm when activated. Lead screw protection cover Digital display settings using function keys ±2% of set speed ±2% of set speed ±0.1% of set speed 0.1mm/min~999.9mm/min Can be set at a pitch of 0.1mm/min Digital display settings using function keys and cursor keys Digital display settings using function keys and cursor keys Digital display settings using cursor keys 300mm (lead screw protection cover included) 5-digit digital display (-signed) SI units and gravity units (kgf) units can be selected using the function keys. The selection of mN, N, kN or gf, kgf, tf is done automatically, but you can also select it arbitrarily.

There are 9 models for this product.

Customers who viewed this product also viewed

Reviews shown here are reviews of companies.

See More Tensile Testers Products

Other products of Sanyu Electronics Industry Co., Ltd.

Reviews shown here are reviews of companies.


View more products of Sanyu Electronics Industry Co., Ltd.

About Company Handling This Product

Response Rate

100.0%


Response Time

72.4hrs

  • Japan

Category of this product

This is the version of our website addressed to speakers of English in the United States. If you are a resident of another country, please select the appropriate version of Metoree for your country in the drop-down menu.

Copyright © 2025 Metoree