LED strobe power supply unit compatible with external digital signal dimming LPS-D3G series
Nissin Electronics Industry Co., Ltd.
About This Product
LED lighting for industrial use and image processing "LED Luminar Series". We create a wide variety of reliable, stable lighting while fully drawing out the excellent characteristics of LEDs, such as long life, power savings, and a variety of colors. In addition to ring type, line type, and transmission type, you can choose from a complete lineup including spot lighting, fiber lighting series, and infrared/ultraviolet LED lighting.
■Power supply for LED lighting Only for spot lighting series Power supply for strobe lighting Overdrive type External digital signal dimming type LPS-D3G SERIES
This is a power supply unit for strobe lighting of the spot lighting series that uses high-brightness power LED elements. Overdrive light emission increases the light intensity by about 5 times for red and about 3 to 4 times for other colors in terms of light emission peak value ratio compared to continuous lighting power supply.
External digital signal dimming type: Dimming can be set in 100 gradations between 25 and 100% using an 8-bit digital signal. Conforms to BCD code. Manual dimming is also possible using a digital switch. (100 steps)
■Features
・Overdrive type strobe light emitting power supply unit dedicated to each series of SP/SK/3VP/FP.
・Emits high-brightness LED light with instantaneous large current
・The light intensity peak level is about 5 times brighter for red when compared to continuous lighting, and about 3 to 4 times brighter for white, blue, and green.
・Synchronized light emission is possible by inputting an external trigger signal.
・Extends the lifespan of LED elements with high-intensity light emission that suppresses heat generation
- Light emission time width can be set arbitrarily using a digital switch
・It is also possible to set and vary the emission time width using an external signal.
・100 gradations of dimming can be controlled using an external 8-bit digital signal. (Peak level variable)
Conforms to BCD code. You can also dim the light in 100 levels using the digital switch on the front panel.
- The dimming range is approximately 25-100%.
■Difference between LPS-D3G and LPS-D3GM
There are LPS-D3G (1 to 990μs) and LPS-D3GM (10μs to 9.9ms) depending on the setting range of the emission time width.
-
Product
LED strobe power supply unit compatible with external digital signal dimming LPS-D3G series
-
Handling Company
Nissin Electronics Industry Co., Ltd.
-
Categories
6 Models of LED strobe power supply unit compatible with external digital signal dimming LPS-D3G series
Items marked with have different values depending on the model number.
Click on the part number for more information about each product
| Product Image | Part Number | Price (excluding tax) | Constant light dimming range | Constant light emission | Digital signal dimming control code | External dimensions (mm) | Input power supply voltage | LED strobe light emission time width control code | LED strobe lighting control cord | Light emission delay time | Light emission synchronization input signal | Light emission time width externally variable | Lighting output | Luminous time width | Mass (kg) | Number of outputs | Strobe dimming range | Strobe light frequency range |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
LPS-D3GS |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 2kHz | LD-KC series S-D type | W152×H101×D206 | AC85~132V | LS-HJ series | LS-SIG series S type | Approximately 5μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 1μs and 990μs (1 to 99μs in 1μs increments, 100 to 990μs in 10μs increments) | Approximately 2.3 |
2 lights 1 channel dimming |
Approximately 25~100% (Variable range of emission peak level, variable by 8-bit digital signal, BCD code) | 0~10kHz (Limited emission time width when used continuously at 100Hz or higher) |
|
|
LPS-D3GMS |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 200Hz | LD-KC series S-D type | W152×H101×D206 | AC85~132V | LS-HJ series | LS-SIG series S type | Approximately 20μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 10μs and 9.9ms (10μs increments from 10 to 990μs, 100μs increments between 1 and 9.9ms) | Approximately 2.3 |
2 lights 1 channel dimming |
Approximately 25~100% (Variable range of emission peak level, variable by 8-bit digital signal, BCD code) | 0~10kHz (Limited emission time width when used continuously at 10Hz or higher) |
|
|
LPS-D3GW |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 2kHz | LD-KC series S-D type | W152×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series W type | Approximately 5μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 1μs and 990μs (1 to 99μs in 1μs increments, 100 to 990μs in 10μs increments) | Approximately 2.5 |
CH1: 2 lights CH2: 2 lights 2 channel independent dimming of each light |
Approximately 25~100% (Variable range of emission peak level, variable by 8-bit digital signal, BCD code) | 0~10kHz (Limited emission time width when used continuously at 100Hz or higher) |
|
|
LPS-D3GMW |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 200Hz | LD-KC series S-D type | W152×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series W type | Approximately 20μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 10μs and 9.9ms (10μs increments from 10 to 990μs, 100μs increments between 1 and 9.9ms) | Approximately 2.5 |
CH1: 2 lights CH2: 2 lights 2 channel independent dimming of each light |
Approximately 25~100% (Variable range of emission peak level, variable by 8-bit digital signal, BCD code) | 0~10kHz (Limited emission time width when used continuously at 10Hz or higher) |
|
|
LPS-D3GT |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 2kHz | LD-KC series S-D type | W182×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series T type | Approximately 5μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 1μs and 990μs (1 to 99μs in 1μs increments, 100 to 990μs in 10μs increments) | Approximately 3.5 |
CH1: 2 lights CH2: 2 lights CH3: 2 lights 3 channels each light independent dimming |
Approximately 25~100% (Variable range of emission peak level, variable by 8-bit digital signal, BCD code) | 0~10kHz (Limited emission time width when used continuously at 100Hz or higher) |
|
|
LPS-D3GMT |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 200Hz | LD-KC series S-D type | W182×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series T type | Approximately 20μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 10μs and 9.9ms (10μs increments from 10 to 990μs, 100μs increments between 1 and 9.9ms) | Approximately 3.5 |
CH1: 2 lights CH2: 2 lights CH3: 2 lights 3 channels each light independent dimming |
Approximately 25~100% (Variable range of emission peak level, variable by 8-bit digital signal, BCD code) | 0~10kHz (Limited emission time width when used continuously at 10Hz or higher) |
Click on the part number for more information about each product
Customers who viewed this product also viewed
Other products of Nissin Electronics Industry Co., Ltd.
View more products of Nissin Electronics Industry Co., Ltd.
