LED lighting for image processing Spot LED/Fiber LED Power supply section LED strobe power supply section Analog volume dimming LPS-3G series
Nissin Electronics Industry Co., Ltd.
About This Product
LED lighting for industrial use and image processing "LED Luminar Series". We create a wide variety of reliable, stable lighting while fully drawing out the excellent characteristics of LEDs, such as long life, power savings, and a variety of colors. In addition to ring type, line type, and transmission type, you can choose from a complete lineup including spot lighting, fiber lighting series, and infrared/ultraviolet LED lighting.
■LED spot lighting Series dedicated lighting power supply Strobe lighting power supply Overdrive type Analog volume dimming type LPS-3G SERIES
This is a power supply unit for strobe lighting for spot lighting SP series/SK series/3VP series and fiber lighting FP series. Overdrive flash instantly emits light approximately 3.5 to 7 times brighter than the peak level. The emission time width can be set arbitrarily from 1μs using a digital switch.
Analog volume dimming type: Dimming can be adjusted between 25 and 100% by manually adjusting the dimming volume.
■Features
・Overdrive type strobe light emitting power supply unit dedicated to each series of SP/SK/3VP/FP.
・Emits high-brightness LED light with instantaneous large current
・The light intensity peak level is about 5 times brighter for red when compared to continuous lighting, and about 3 to 4 times brighter for white, blue, and green.
・Synchronized light emission is possible by inputting an external trigger signal.
・Extends the lifespan of LED elements with high-intensity light emission that suppresses heat generation
- Light emission time width can be set arbitrarily using a digital switch
・It is also possible to set and vary the emission time width using an external signal.
・Dimmer can be adjusted from 25 to 100% with analog volume (peak level variable)
・Differences between 3G series and 3GM series
The strobe lighting power supply dedicated to the spot lighting series is divided into the 3G series (1 to 990μs) and the 3GM series (10μs to 9.9ms), depending on the variable range of the light emission time width.
specification
■For strobe lighting
Compatible with AC85-132V. AC85~264V specification products are also available. ("-2" is added to the end of the model number)
-
Product
LED lighting for image processing Spot LED/Fiber LED Power supply section LED strobe power supply section Analog volume dimming LPS-3G series
-
Handling Company
Nissin Electronics Industry Co., Ltd.
-
Categories
6 Models of LED lighting for image processing Spot LED/Fiber LED Power supply section LED strobe power supply section Analog volume dimming LPS-3G series
Items marked with have different values depending on the model number.
Click on the part number for more information about each product
| Product Image | Part Number | Price (excluding tax) | Constant light dimming range | Constant light emission | External dimensions (mm) | Input power supply voltage | LED strobe light emission time width control code | LED strobe lighting control cord | Light emission delay time | Light emission synchronization input signal | Light emission time width externally variable | Lighting output | Luminous time width | Mass (kg) | Number of outputs | Strobe dimming range | Strobe light frequency range |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
LPS-3GS |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 2kHz | W152×H101×D206 | AC85~132V | LS-HJ series | LS-SIG series S type | Approximately 5μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 1μs and 990μs (1 to 99μs in 1μs increments, 100 to 990μs in 10μs increments) | Approximately 2.3 |
2 lights 1 channel dimming |
Approximately 25~100% (depending on the variable range of light emission peak level and variable dimming volume) | 0~10kHz (Limited emission time width when used continuously at 100Hz or higher) |
|
|
LPS-3GMS |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 200Hz | W152×H101×D206 | AC85~132V | LS-HJ series | LS-SIG series S type | Approximately 20μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 10μs and 9.9ms (10μs increments from 10 to 990μs, 100μs increments between 1 and 9.9ms) | Approximately 2.3 |
2 lights 1 channel dimming |
Approximately 25~100% (depending on the variable range of light emission peak level and variable dimming volume) | 0~10kHz (Limited emission time width when used continuously at 10Hz or higher) |
|
|
LPS-3GW |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 2kHz | W152×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series W type | Approximately 5μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 1μs and 990μs (1 to 99μs in 1μs increments, 100 to 990μs in 10μs increments) | Approximately 2.5 |
CH1: 2 lights CH2: 2 lights 2 channel independent dimming of each light |
Approximately 25~100% (depending on the variable range of light emission peak level and variable dimming volume) | 0~10kHz (Limited emission time width when used continuously at 100Hz or higher) |
|
|
LPS-3GMW |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 200Hz | W152×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series W type | Approximately 20μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 10μs and 9.9ms (10μs increments from 10 to 990μs, 100μs increments between 1 and 9.9ms) | Approximately 2.5 |
CH1: 2 lights CH2: 2 lights 2 channel independent dimming of each light |
Approximately 25~100% (depending on the variable range of light emission peak level and variable dimming volume) | 0~10kHz (Limited emission time width when used continuously at 10Hz or higher) |
|
|
LPS-3GT |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 2kHz | W182×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series T type | Approximately 5μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 1μs and 990μs (1 to 99μs in 1μs increments, 100 to 990μs in 10μs increments) | Approximately 3.5 |
CH1: 2 lights CH2: 2 lights CH3: 2 lights 3 channels each light independent dimming |
Approximately 25~100% (depending on the variable range of light emission peak level and variable dimming volume) | 0~10kHz (Limited emission time width when used continuously at 100Hz or higher) |
|
|
LPS-3GMT |
Available upon quote | Approximately 25~100% when using dimming volume / 0~100% when using light width setting switch (100 steps) | Continuous lighting at approximately 200Hz | W182×H101×D256 | AC85~132V | LS-HJ series | LS-SIG series T type | Approximately 20μs from trigger signal input to start of light emission | TTL+ or open collector | External control possible with open collector (selector switch must be operated manually) | DC5~12V (no load) *The output has a built-in series resistor, and the output voltage changes depending on the load. | Between 10μs and 9.9ms (10μs increments from 10 to 990μs, 100μs increments between 1 and 9.9ms) | Approximately 3.5 |
CH1: 2 lights CH2: 2 lights CH3: 2 lights 3 channels each light independent dimming |
Approximately 25~100% (depending on the variable range of light emission peak level and variable dimming volume) | 0~10kHz (Limited emission time width when used continuously at 10Hz or higher) |
Click on the part number for more information about each product
Customers who viewed this product also viewed
Other products of Nissin Electronics Industry Co., Ltd.
View more products of Nissin Electronics Industry Co., Ltd.
