Low voltage insulation monitoring system i-moni-ZE-1NF

Low voltage insulation monitoring system i-moni-ZE-1NB

Low voltage insulation monitoring system i-moni-ZE-1RF

Low voltage insulation monitoring system i-moni-ZE-1RB

Low voltage insulation monitoring system i-moni-ZE-2NF

Low voltage insulation monitoring system i-moni-ZE-2NB

Low voltage insulation monitoring system i-moni-ZE-2RF

Low voltage insulation monitoring system i-moni
Kyushu Kiden Co., Ltd.

Kyushu Kiden Co., Ltd.'s Response Status

Response Rate

100.0%

Response Time

38.0hours

Company Review

5.0

About This Product

■SummaryEliminate wasted energy due to sudden accidents. Extending annual inspections significantly reduces test costs. Leave the preventive maintenance of electrical equipment essential to factories and buildings to Hitachi Low Voltage Insulation Monitoring System.

■Advantages of introducing insulation monitoring・24-hour monitoring eliminates the need for power outages.
・Early detection of signs of insulation deterioration and proactive management possible. (Preventive maintenance)
・Insulation resistance test during annual inspection can be reduced.

■Economical and space saving-Multi-circuit insulation monitoring unit facilitates construction and saves space. The cost per circuit can also be reduced.
・It is economical and saves space because no voltage superimposition device is required. It does not affect the electrical circuit or load.

■Stable operation using the same detection method as earth leakage circuit breakers・Similar to proven earth leakage circuit breakers, this is a highly reliable method that uses the magnitude of the detected leakage current as is.
- To judge the insulation state, the "leakage current fundamental wave component", which is obtained by removing harmonic components from the detected leakage current, is used.

■Appropriate monitoring of effective leakage current depending on the type of circuit・Single-phase and three-phase - △ Connection (S phase grounding): The fundamental wave capacitor component (I0r) shows a large value, so monitor the fundamental wave effective component I0r.
・Three-phase - Y connection (neutral point grounded): Monitored by fundamental wave I0 (≒I0r). Since the total fundamental wave capacitor component (I0c) of each phase is extremely small, monitoring the fundamental wave means monitoring the effective fundamental wave component.

■Data can be collected using H-NET standard software・Standard software for the power distribution and utility monitoring system (H-NET) allows for easy proactive management by continuously collecting data and understanding trends.
・It is possible to narrow down lines with insulation deterioration by analyzing the operating status of equipment.

There are other model numbers as well.

Model
There are 10 models for this product.

Product
Low voltage insulation monitoring system i-moni

Handling Company
Kyushu Kiden Co., Ltd.

Categories

Safety Devices

Insulation Monitors

320+ people viewing

Free
Get started with our free quotation service - no cost, no obligation.

No Phone Required
We respect your privacy. You can receive quotes without sharing your phone number.

10 Models of Low voltage insulation monitoring system i-moni

Click on the part number for more information about each product

Part Number	Price (excluding tax)	Communication protocol	Communication interface	Tolerance Effective leakage current (Ior)	Tolerance Fundamental leakage current (Io)	Setting voltage system (phase wire system)	Setting Monitoring value (warning, caution)	Setting ZCT type	Meter measurement range	Measurement item Fundamental leakage current (Io)	Measurement item Fundamental wave effective leakage current (Ior)	Display Measured value	Display Monitored value (warning, caution)	Monitoring alarm output	Monitoring Monitoring level	Monitoring Fault output	Earth leakage display method	Compliant standards	Detection current	Return method	Rated inertial dead time	Rated sensitivity current	Rated operating time	Rated non-operating current	Item	Output item Effective leakage current monitoring circuit	Output item Fundamental wave leakage current monitoring circuit	Number of input voltage systems	Input adaptive circuit	Relay contact configuration	Testing mechanism
ZE-1NF	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	1 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-1NB	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	1 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-1RF	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	1 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-1RB	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	1 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-2NF	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	2 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-2NB	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	2 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-2RF	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	2 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-2RB	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	2 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-6NF3	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	6 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)
ZE-6NB3	Available upon quote	H-NET, Modbus®/RTU	RS-485	±10% of fundamental wave leakage current ±1mA	Indication value error ±5% ±1mA	Three-phase three-wire (△): Monitors effective leakage current Single-phase 2-wire/3-wire: Monitors effective leakage current Others (3-phase 3-wire (Y), 3-phase 4-wire): Monitors fundamental wave leakage current.	2~999mA (Set unmonitored circuits to default 1000mA)	Model selection (ZR series, ZCT built-in fuse-free circuit breaker, etc.)	0~999.9mA If 1000mA or more is detected, the measurement will be over.	0~999.9mA ZCT output current (leakage current) minus DC and harmonic components	Extraction of the effective component of the fundamental wave (component in phase with the ground phase voltage)	Fundamental leakage current, effective leakage current 0.0~999.9mA (all over 1000mA will be displayed as OL) If display of effective leakage current is selected in the circuit that monitors fundamental leakage current, "----" will be displayed I will	2~999mA (Circuit not monitored will display default 1000mA)	Relay A contact x 2 per circuit (warning, caution) If the follow-up action earth leakage relay function is included, there is also 1 a contact for each circuit.	You can set the warning level and caution level for each circuit (please set it so that warning ≥ caution)	Relay a contact x 1 (ERR)	Light emitting diode (LED: red)	JISC8374:1991 Earth leakage relay	Detection current similar to conventional earth leakage relays	Manual recovery using the reset button (reset method for each circuit)	1,0.5,0.25,0.15,0.1 seconds	2,000, 1,000, 500, 200, 100mA	2,1,0.5,0.3,0.2 seconds time delay type	1,000, 500, 250, 100, 50mA	6 circuit product	Analog output of effective leakage current measurement value	Analog output of fundamental wave leakage current measurement value	1 system: 1 circuit product, 6 circuits/10 circuits with earth leakage relay function 2 systems: Other than above	Low voltage circuit with line voltage AC440V or less (transformer grounding wire, each feeder) 50/60Hz	A contact (normally open)	Manual test using test button (test method for each circuit)

Click on the part number for more information about each product

Customers who viewed this product also viewed

Reviews shown here are reviews of companies.

Insulation resistance monitoring device IRS (1 unit monitoring/standard version)

Takenaka Electric Co., Ltd.

240+ people viewing

Last viewed: 16 hours ago

Response time: 13.13 hours

Insulation Monitors

6 models listed

Insulation resistance monitoring device IRS (9 units monitoring/high-performance version)

Takenaka Electric Co., Ltd.

130+ people viewing

Last viewed: 20 hours ago

Response time: 13.13 hours

Insulation Monitors

4 models listed

Electrical insulation diagnosis Q (t) meter AD-9832A

A and Day Co., Ltd.

270+ people viewing

Last viewed: 23 minutes ago

Response time: 26.37 hours

Insulation Monitors

2 models listed

See More Insulation Monitors Products

Other products of Kyushu Kiden Co., Ltd.

Reviews shown here are reviews of companies.

Inverter control V type Air dryer built-in/mounted package Bebicon (non-lube type)

Kyushu Kiden Co., Ltd.

5.0

330+ people viewing

Last viewed: 19 minutes ago

Response time: 38.04 hours

Air Compressors

4 models listed

Air dryer built-in/equipped package Bebicon (non-lube type)

Kyushu Kiden Co., Ltd.

5.0

450+ people viewing

Response time: 38.04 hours

Air Compressors

10 models listed

Package Bebicon (non-lube type)

Kyushu Kiden Co., Ltd.

5.0

480+ people viewing

Last viewed: 17 minutes ago

Response time: 38.04 hours

Air Compressors

10 models listed

Air dryer built-in/equipped package Bebicon (lubrication type)

Kyushu Kiden Co., Ltd.

5.0

500+ people viewing

Last viewed: 19 hours ago

Response time: 38.04 hours

Air Compressors

10 models listed

Package Bebicon (refueling type)

Kyushu Kiden Co., Ltd.

5.0

460+ people viewing

Response time: 38.04 hours

Air Compressors

10 models listed

Medium pressure package with built-in air dryer Bebicon (lube type)

Kyushu Kiden Co., Ltd.

5.0

440+ people viewing

Last viewed: 54 minutes ago

Response time: 38.04 hours

Air Compressors

8 models listed

Air dryer equipped medium pressure package Bebicon (non-lube type)

Kyushu Kiden Co., Ltd.

5.0

170+ people viewing

Last viewed: 7 hours ago

Response time: 38.04 hours

Air Compressors

2 models listed

Pressure switch type package Bebicon

Kyushu Kiden Co., Ltd.

5.0

280+ people viewing

Last viewed: 22 hours ago

Response time: 38.04 hours

Air Compressors

8 models listed

Lubrication type Bebicon Pressure switch type

Kyushu Kiden Co., Ltd.

5.0

580+ people viewing

Response time: 38.04 hours

Air Compressors

10 models listed

Lubrication type Bebicon automatic unloader type

Kyushu Kiden Co., Ltd.

5.0

580+ people viewing

Response time: 38.04 hours

Air Compressors

10 models listed

Industrial IJ printer Gravis UX series for lowercase letters

Kyushu Kiden Co., Ltd.

5.0

400+ people viewing

Response time: 38.04 hours

Inkjet Printers

4 models listed

High efficiency permanent magnet motor (PM motor) IE4

Kyushu Kiden Co., Ltd.

5.0

770+ people viewing

Last viewed: 6 hours ago

Response time: 38.04 hours

Permanent Magnet Motors

40 models listed

View more products of Kyushu Kiden Co., Ltd.

About Company Handling This Product

Kyushu Kiden Co., Ltd.

Response Rate

100.0%

Response Time

38.0hrs

Company Review

5.0

Japan

Related search keywords

This is the version of our website addressed to speakers of English in the United States. If you are a resident of another country, please select the appropriate version of Metoree for your country in the drop-down menu.

Low voltage insulation monitoring system i-moni Kyushu Kiden Co., Ltd.

Kyushu Kiden Co., Ltd.'s Response Status

About This Product

■Summary

■Advantages of introducing insulation monitoring

■Economical and space saving

■Stable operation using the same detection method as earth leakage circuit breakers

■Appropriate monitoring of effective leakage current depending on the type of circuit

■Data can be collected using H-NET standard software

10 Models of Low voltage insulation monitoring system i-moni

Customers who viewed this product also viewed

Other products of Kyushu Kiden Co., Ltd.

About Company Handling This Product

Related search keywords

Low voltage insulation monitoring system i-moni
Kyushu Kiden Co., Ltd.