Various vibration switches PRO
BATROSS Co., Ltd.

PRO440

Approximately 1.8kg

EMC:FCC47CFR, 15-B, classA, ANSIC63.4, CSA:CLASSⅠ, DIV2, (B-D), T4, CLASSⅡ, DIV2, (F, G), T4

Copper-free aluminum casting

Epoxy powder coating (blue)

NEMA4X/IP65

100%

≦10G (If the vibration exceeds 10G when measured on-site, install the PRO Switch remotely using an external sensor.)

-40~+70℃

DC24V@25mA (4-20mA-type), DC24V@4mA (rated current & piezo speed), DC12V bias voltage (moving coil speed)

1 unit (2 units optional), SPDT (C type), minimum switching capacity DC100mA@DC5V, maximum capacity AC2,500VA/10A@AV250V, DC5A@DC100V, normally open/closed mutual use

Connection terminal: Inside the PRO housing, BNC terminal: Inside the PRO450 housing, Impedance: 1kΩ, Short protection circuit included, Accuracy: ±5% (measured value), 3dB bandwidth: 20kHz, Cable movable: Maximum length 305m

8 characters x 2 lines, 4 x 7 green dot character display, Resolution: 5 pixels, Displays instantaneous values ​​and their units, You can access the settings menu to change the display and settings, and reset them on the spot.

4 membrane keypad, ``→'' ``↓'' ``MENU'' ``ENTER''

Yellow: In alarm, Red: Shutdown (dual relay only), Off: Not in alarm

Green: Sensor connection OK, Red: Sensor connection NG, Off: SW is not powered on.

Red: SW is in bypass mode, off: SW is in non-bypass mode

Number of outputs: 1, Accuracy: ±1%/full scale, 4mA±0.25mA@minimum, Power supply: DC24V, Short protection circuit included, Dead band current: 3.8mA, Maximum output DC20mA (100%F.S.)

Nominal current 17.5A, maximum load current 22A, nominal voltage AC250V, rated voltage AC320V, insulation polyimide, flame retardant (UL94) V0

AC85~230V/50~60Hz, DC24V (The input power supply must be specified at the time of ordering, and the power supply specifications cannot be changed after installation.)

6W or less

AC5V (p-p): All mV sensor input, DC20mA: All converter input

Acceleration, velocity, integrated acceleration, impact force, DC4~20mA

Reset retention alarm. Use the alarm reset feature to reset in the field via keypad or display. Remote reset is possible if there is not enough RST terminal temporarily.

20~127mm/sec

50~500m/sec^2, 20~117mm/sec

50~100m/sec^2, 20~76mm/sec

-999.9~+999.9

It is energized by shorting the BYP terminal. Bypass status is maintained as long as the terminals continue to be shorted. Monitoring will resume when the short is removed.

Moving coil speed (configurable): 10kΩ, 100kΩ, constant current sensor: 4mA bias (automatically adjusted to maintain current), DC4~20mA converter: 100Ω

1

PRO6000

Approximately 1.8kg

EMC:FCC47CFR, 15-B, classA, ANSIC63.4, CSA:CLASSⅠ, DIV1, (B-D), T4A, CLASSⅡ, DIV1, (E-G), T4A

Copper-free aluminum casting

Epoxy powder coating (blue)

NEMA4, explosion-proof

100%

≦10G (If the vibration exceeds 10G when measured on-site, install the PRO Switch remotely using an external sensor.)

-40~+70℃

DC24V@25mA (4-20mA-type), DC24V@4mA (rated current & piezo speed), DC12V bias voltage (moving coil speed)

1 unit (2 units optional), SPDT (C type), minimum switching capacity DC100mA@DC5V, maximum capacity AC2,500VA/10A@AV250V, DC5A@DC100V, normally open/closed mutual use

Connection terminal: Inside the PRO housing, BNC terminal: Inside the PRO450 housing, Impedance: 1kΩ, Short protection circuit included, Accuracy: ±5% (measured value), 3dB bandwidth: 20kHz, Cable movable: Maximum length 305m

8 characters x 2 lines, 4 x 7 green dot character display, Resolution: 5 pixels, Displays instantaneous values ​​and their units, You can access the settings menu to change the display and settings, and reset them on the spot.

4 membrane keypad, ``→'' ``↓'' ``MENU'' ``ENTER''

Yellow: In alarm, Red: Shutdown (dual relay only), Off: Not in alarm

Green: Sensor connection OK, Red: Sensor connection NG, Off: SW is not powered on.

Red: SW is in bypass mode, off: SW is in non-bypass mode

Number of outputs: 1, Accuracy: ±1%/full scale, 4mA±0.25mA@minimum, Power supply: DC24V, Short protection circuit included, Dead band current: 3.8mA, Maximum output DC20mA (100%F.S.)

Nominal current 17.5A, maximum load current 22A, nominal voltage AC250V, rated voltage AC320V, insulation polyimide, flame retardant (UL94) V0

AC85~230V/50~60Hz, DC24V (The input power supply must be specified at the time of ordering, and the power supply specifications cannot be changed after installation.)

6W or less

AC5V (p-p): All mV sensor input, DC20mA: All converter input

Acceleration, velocity, integrated acceleration, impact force, DC4~20mA

Reset retention alarm. Use the alarm reset feature to reset in the field via keypad or display. Remote reset is possible if there is not enough RST terminal temporarily.

20~127mm/sec

50~500m/sec^2, 20~117mm/sec

50~100m/sec^2, 20~76mm/sec

-999.9~+999.9

It is energized by shorting the BYP terminal. Bypass status is maintained as long as the terminals continue to be shorted. Monitoring will resume when the short is removed.

Moving coil speed (configurable): 10kΩ, 100kΩ, constant current sensor: 4mA bias (automatically adjusted to maintain current), DC4~20mA converter: 100Ω

1

PRO450

Approximately 1.8kg

EMC:FCC47CFR, 15-B, classA, ANSIC63.4, CSA/UL:CLASSⅠ, DIV1, (GROUP:B-D) , CLASSⅡ, DIV1, (GROUP:E-G)

Copper-free aluminum casting

Painted (gray) (Optionally, colored epoxy resin coating is also available. The housing is NEMA4 level regardless of whether or not it is coated with epoxy resin.)

NEMA4X/IP65, explosion-proof

100%

≦10G (If the vibration exceeds 10G when measured on-site, install the PRO Switch remotely using an external sensor.)

-40~+70℃

DC24V@25mA (4-20mA-type), DC24V@4mA (rated current & piezo speed), DC12V bias voltage (moving coil speed)

1 unit (2 units optional), SPDT (C type), minimum switching capacity DC100mA@DC5V, maximum capacity AC2,500VA/10A@AV250V, DC5A@DC100V, normally open/closed mutual use

Connection terminal: Inside the PRO housing, BNC terminal: Inside the PRO450 housing, Impedance: 1kΩ, Short protection circuit included, Accuracy: ±5% (measured value), 3dB bandwidth: 20kHz, Cable movable: Maximum length 305m

8 characters x 2 lines, 4 x 7 green dot character display, Resolution: 5 pixels, Displays instantaneous values ​​and their units, You can access the settings menu to change the display and settings, and reset them on the spot.

4 membrane keypad, ``→'' ``↓'' ``MENU'' ``ENTER''

Yellow: In alarm, Red: Shutdown (dual relay only), Off: Not in alarm

Green: Sensor connection OK, Red: Sensor connection NG, Off: SW is not powered on.

Red: SW is in bypass mode, off: SW is in non-bypass mode

Number of outputs: 1, Accuracy: ±1%/full scale, 4mA±0.25mA@minimum, Power supply: DC24V, Short protection circuit included, Dead band current: 3.8mA, Maximum output DC20mA (100%F.S.)

Nominal current 17.5A, maximum load current 22A, nominal voltage AC250V, rated voltage AC320V, insulation polyimide, flame retardant (UL94) V0

AC85~230V/50~60Hz, DC24V (The input power supply must be specified at the time of ordering, and the power supply specifications cannot be changed after installation.)

6W or less

AC5V (p-p): All mV sensor input, DC20mA: All converter input

Acceleration, velocity, integrated acceleration, impact force, DC4~20mA

Reset retention alarm. Use the alarm reset feature to reset in the field via keypad or display. Remote reset is possible if there is not enough RST terminal temporarily.

20~127mm/sec

50~500m/sec^2, 20~117mm/sec

50~100m/sec^2, 20~76mm/sec

-999.9~+999.9

It is energized by shorting the BYP terminal. Bypass status is maintained as long as the terminals continue to be shorted. Monitoring will resume when the short is removed.

Moving coil speed (configurable): 10kΩ, 100kΩ, constant current sensor: 4mA bias (automatically adjusted to maintain current), DC4~20mA converter: 100Ω

1