Electric micropipette MPA series
A and Day Co., Ltd.
About This Product
A&D's MPA series is
・Because it is electric, it is accurate, speedy, and fatigue-free.
・Even though it is electric, it is light, hard to break, and affordable.
■High precision
・Reduced variation in dispensing amount between individuals
・Ensure high reproducibility
・Accurately aspirates and dispenses the set amount
・Suction and discharge speeds can each be set in 5 steps (highly viscous samples can also be dispensed with high precision)
■Strong against organic solvents and acids
・Glass chips available (for MPA-200/MPA-1200/MPA-10000)
・Designed to withstand the use of organic solvents:
・Chip holder using fluororesin (PVDF)
・Fluorinated grease with excellent acid and chemical resistance is used on the piston.
・Special glass chips can also be used.
■Easy operation
Instead of moving the piston up and down with your thumb, you operate the button with your index finger.
■Five mode settings to suit your purpose
・Continuous dispensing mode (MD): Equal amounts can be dispensed with one suction
・Mixing mode (MIX): Pipetting the set volume x number of times with one push
・Dispensing mixing mode (AUTO+MIX): Continuous mixing (stirring) after dispensing
・Sequential suction mode (SA): After aspirating a set volume of different liquids, the entire amount is discharged.
・Sequential discharge mode (SD): Dispense the same sample into different volumes
■Tips made by other companies can also be used.
Chips made by other companies can also be used.
■No need to dispose of dispensing
Pre-dispense function Unique pre-dispense function eliminates the need for initial dispensing.
■User calibration function [patented]
You can check the capacity of your pipette by using the optional pipette capacity tester, but you can also calibrate it further using the user calibration function. In addition to the original purpose of checking accuracy, for example, even if you use your "favorite chip", you can use it without any problems by calibrating its capacity.
User CAL function - Daily maintenance and management of micropipette accuracy - Possible to calibrate using the tip used and the liquid to be dispensed
■Mass (mg) Mode [Patented]
In addition to volume (μL), mass (mg) can be dispensed. Units are compatible even when mixing liquids with samples that are controlled by mass, such as solids or powders. In addition, the reverse mode and mg display allow accurate control of the dispensed amount of high viscosity test liquids, which are prone to errors with normal volume calibration.
■Concentration calculation possible
Calibration and display function using mass (mg) Concentration calculation is possible by measuring liquid in mg
-
Product
Electric micropipette MPA series
-
Handling Company
A and Day Co., Ltd.
-
Categories
5 Models of Electric micropipette MPA series
Items marked with have different values depending on the model number.
Click on the part number for more information about each product
| Product Image | Part Number | Price (excluding tax) | AC adapter AC100V 50/60Hz | Autoclave treatment | Battery | Capacity range | Charging time | Dispensing speed | Energy saving settings | Full length | Mass | Material | Maximum number of dispenses (at full charge) | Maximum number of dispensing (continuous dispensing) | Operating environment temperature | Operating mode | Performance: Accuracy | Performance: Repeatability (CV) | Performance: capacity | Pipette drive system | Program memory |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
MPA-10 |
$ 273.00〜 | DC5V/1A (Standard accessory, for charging, can be used while charging) | Possible only at the bottom of the main body | Lithium ion battery 3.7V/920mAh | 0.3~10μL | Approximately 5 hours / 100% charge | 5 step adjustment | Auto power off after 10 minutes | Approximately 280mm | Approximately 150g | Pipette body: ABS, Ejector: PP (20% glass fiber), Tip holder: PVDF, Piston: SUS | Approximately 1,800 times (in standard mode, maximum suction/discharge speed setting) | 0.3μL×33 times | 15~30℃ | Standard mode (AUTO), continuous dispensing mode (MD), mixed mode (MIX), system setting mode (SYS) | ±4.0% / ±2.0% / ±1.0% | 2.5% / 0.8% / 0.4% | 1.0μL / 5.0μL / 10.0μL | High performance stepping motor | 9 types |
|
|
MPA-20 |
$ 273.00〜 | DC5V/1A (Standard accessory, for charging, can be used while charging) | Possible only at the bottom of the main body | Lithium ion battery 3.7V/920mAh | 0.3~20μL | Approximately 5 hours / 100% charge | 5 step adjustment | Auto power off after 10 minutes | Approximately 280mm | Approximately 150g | Pipette body: ABS, Ejector: PP (20% glass fiber), Tip holder: PVDF, Piston: SUS | Approximately 1,800 times (in standard mode, maximum suction/discharge speed setting) | 0.3μL x 66 times | 15~30℃ | Standard mode (AUTO), continuous dispensing mode (MD), mixed mode (MIX), system setting mode (SYS) | ±4.0% / ±2.0% / ±1.0% | 2.5% / 0.8% / 0.4% | 2.0μL / 10.0μL / 20.0μL | High performance stepping motor | 9 types |
|
|
MPA-200 |
$ 273.00〜 | DC5V/1A (Standard accessory, for charging, can be used while charging) | Possible only at the bottom of the main body | Lithium ion battery 3.7V/920mAh | 3.0~200μL | Approximately 5 hours / 100% charge | 5 step adjustment | Auto power off after 10 minutes | Approximately 280mm | Approximately 160g | Pipette body: ABS, Ejector: PP (20% glass fiber), Tip holder: PVDF, Piston: SUS | Approximately 1,800 times (in standard mode, maximum suction/discharge speed setting) | 3μL x 66 times | 15~30℃ | Standard mode (AUTO), continuous dispensing mode (MD), mixed mode (MIX), system setting mode (SYS) | ±2.5% / ±1.2% / ±0.6% | 1.0% / 0.3% / 0.15% | 10μL / 100μL / 200μL | High performance stepping motor | 9 types |
|
|
MPA-1200 |
$ 273.00〜 | DC5V/1A (Standard accessory, for charging, can be used while charging) | Possible only at the bottom of the main body | Lithium ion battery 3.7V/920mAh | 15~1200μL | Approximately 5 hours / 100% charge | 5 step adjustment | Auto power off after 10 minutes | Approximately 280mm | Approximately 170g | Pipette body: ABS, Ejector: PP (20% glass fiber), Tip holder: PVDF, Piston: SUS | Approximately 1,800 times (in standard mode, maximum suction/discharge speed setting) | 15μL x 80 times | 15~30℃ | Standard mode (AUTO), continuous dispensing mode (MD), mixed mode (MIX), system setting mode (SYS) | ±2.5% / ±1.0% / ±0.5% | 0.6% / 0.3% / 0.15% | 100μL / 600μL / 1200μL | High performance stepping motor | 9 types |
|
|
MPA-10000 |
$ 273.00〜 | DC5V/1A (Standard accessory, for charging, can be used while charging) | Possible only at the bottom of the main body | Lithium ion battery 3.7V/920mAh | 0.1~10.0mL | Approximately 5 hours / 100% charge | 5 step adjustment | Auto power off after 10 minutes | Approximately 280mm | Approximately 190g | Pipette body: ABS, Ejector: PP (20% glass fiber), Tip holder: PVDF, Piston: PVDF | Approximately 1,800 times (in standard mode, maximum suction/discharge speed setting) | 0.1mL x 99 times | 15~30℃ | Standard mode (AUTO), continuous dispensing mode (MD), mixed mode (MIX), system setting mode (SYS) | ±2.5% / ±1.0% / ±0.5% | 0.6% / 0.15% / 0.15% | 1.0mL / 5.0mL / 10.0mL | High performance stepping motor | 9 types |
Click on the part number for more information about each product
Customers who viewed this product also viewed
Other products of A and Day Co., Ltd.
View more products of A and Day Co., Ltd.
About Company Handling This Product
- Japan