All Categories
History
Price (excluding tax)
Response Rate
100.0%
Response Time
69.4hours
■Features
・Easy to operate, economical cutter
・Cutter can be installed by simply tightening the pin, and there is no need to adjust the right angle to the table, making setup easy.
・The cutter arbor is guided even at the top of the table to prevent it from falling over and prevent it from escaping.
・When using two blades, rough cutting and finishing can be done at the same time. Single blade can also be used, and resharpening is possible.
・Operation where the cutter does not process, the table moves back so that the cutting edge escapes from bottom to top
・Table feed is 6 steps up to 0.18mm in 3/100 units, automatic feed, automatic stop
・The table can be moved in the depth of cut direction and in the left and right directions, so the width can be expanded.
・This machine is small and does not take up much space, and is easy to operate and clamp the workpiece.
・The start switch cannot be turned on unless the table is returned to its origin.
・Cutting stops at bottom dead center
・Blade can be re-sharpened
■Operating procedure
・Attach the arbor
・Place the workpiece on top
・Loosen the arbor guide clamp and adjust the arbor guide to the height of the workpiece.
・Place the workpiece on the workpiece centering tombstone and clamp the workpiece with the workpiece clamp.
・Move the arm forward with the arm forward/backward movement handle and clamp it with the arm clamp.
・Determine the internal position using the table front and back feed handle
・Set the depth of cut with the scale of the depth of cut adjustment bolt, and determine the feed amount of the 1-stroke feed adjustment plate (0.03 mm per scale)
・Air cut (0.3mm) and return with table front/rear feed handle
・Start switch (safety device) set
・Press the start switch and turn on the coolant pump ON/OFF coolant switch.
・Set the automatic feed handle of the automatic feed/off lever to
You can search for other models from each index. The displayed value is the value of the currently selected part number.
1 stroke depth of cut
1 stroke table return
Arm front and rear/arm clamp
Bottom dimension from arbor back to column (mm)
Control method
Floor to table height (mm)
Lubricating oil pump (centralized lubrication)
Main motor *3 phase 200V
Maximum cutting length when using 1 flute (mm)
Maximum cutting length when using 2 flutes (mm)
Maximum outer diameter of workpiece when using inner diameter reference guide sesame
Minimum inner diameter of workpiece
Outer diameter (tombstone) Maximum outer diameter of workpiece at standard time
Piston stroke (mm)
Processing key width (mm)
Required floor area (mm)
Return to table start position after cutting
Specification name
Spindle drum rotation speed (RPM)
Table movement back and forth (mm)
Table movement left and right
Table surface size (mm)
Weight (kg)
Pneumatic cylinder (arm clamp)
Pneumatic cylinder (front and rear of arm)
Pneumatic cylinder (work clamp)
Rotary actuator (feed in/off)
Table return motor
Ac servo motor
Floor level to top of indicator light height
Part Number
TK-150A-SHandling Company
Takara Machine Industry Co., Ltd.Categories
| Image | Price (excluding tax) | 1 stroke depth of cut | 1 stroke table return | Arm front and rear/arm clamp | Bottom dimension from arbor back to column (mm) | Control method | Floor to table height (mm) | Lubricating oil pump (centralized lubrication) | Main motor *3 phase 200V | Maximum cutting length when using 1 flute (mm) | Maximum cutting length when using 2 flutes (mm) | Maximum outer diameter of workpiece when using inner diameter reference guide sesame | Minimum inner diameter of workpiece | Outer diameter (tombstone) Maximum outer diameter of workpiece at standard time | Piston stroke (mm) | Processing key width (mm) | Required floor area (mm) | Return to table start position after cutting | Specification name | Spindle drum rotation speed (RPM) | Table movement back and forth (mm) | Table movement left and right | Table surface size (mm) | Weight (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
Available upon quote | 0.03mm unit 0.03~0.18 | 0.30mm-depth of cut | Manual | 345 | Relay | 1,000 | Manual | 1.5KW6P | 130 | 100 | Approximately 700φ | 8φ | Approximately 300φ | 150 | 3~20 | 550×850 | Manual | Standard machine | 27/22 | 60 | 25mm each | 560×570 | 800 |
Reviews shown here are reviews of companies.
Reviews shown here are reviews of companies.
Response Rate
100.0%
Response Time
69.4hrs
