Riken Kiki Co., Ltd.

Both ends have R (male thread) fittings. Basically, it is used by attaching the H side coupler to one side.

• Polymeric Materials

• Nylon Tubing

This is a manual pump with a maximum working pressure of 100MPa, and has a two-speed function that automatically switches betwe...

• Pumps

• Hydraulic Pumps

This pressure gauge has a load scale (kN) corresponding to the pressure-receiving area (push side) of the cylinder on the press...

• Meters & Instruments

• Pressure Gauges

Normally it is an internal pilot, but if you rotate the head 180 degrees, it becomes an external pilot. (Pilot port connection ...

• Valves

• Counterbalance Valves

Hydraulic bolt tensioners use cylinders to apply tension to bolts and stud bolts, and use their elasticity to apply a certain t...

• Fastening Components

• Bolt & Stud Tensioners

• Pumps

• Hydraulic Pumps

• Pumps

• Hydraulic Pumps

Can cut carbon steel bars, special steel bars, etc. The blades are designed so that they do not come into direct contact with e...

• Machining / Machine Tools

• Metal Cutting Shears

• Pumps

• Hydraulic Pumps

The feature is that there is little pressure fluctuation. When adjusting the pressure, loosen the lock nut and gradually turn t...

• Valves

• Control Pressure Valves

Each cylinder comes with a cap on the tip of the piston.

• Drive Mechanisms & Components

• Cylinders

This is a pressure gauge that can be used with tap water as the working fluid. Because it is a universal screw, the direction o...

• Meters & Instruments

• Pressure Gauges

The air source operates the pump piston and generates 200MPa of oil pressure. It is lightweight, compact, and easy to operate. ...

• Pumps

• Hydraulic Pumps

Connect the drain port directly to the oil tank.

• Valves

• Control Pressure Valves

Because it uses ultra-high strength aluminum material, it weighs approximately 1/2 of the standard cylinder. The entire surface...

• Drive Mechanisms & Components

• Cylinders

This is a manual pump that can boost the pressure to ultra-high pressures of 300MPa and 400MPa. Work efficiency can be improved...

• Pumps

• Hydraulic Pumps

• Drive Mechanisms & Components

• Cylinders

The coil has a continuous rating, so it can be energized for a long time. Since it is a poppet type, there is almost no oil lea...

• Valves

• Solenoid Valves

Mainly used for electric pumps such as EMP-5SW, EMP-6SW (SB), MP-10SW (SB), MP-12SW (SB), MP-15S, etc. A push button switch is ...

• Controllers

• Control Panels

• Pumps

• Hydraulic Pumps

Tap water can be used as the working fluid up to 70MPa. The material of the base is stainless steel. Standard total length is 2...

• Polymeric Materials

• Nylon Tubing

Flow rate adjustment valve with bypass check valve. The flow rate can be adjusted with a needle type. You can set the repeatabi...

• Valves

• Flow Control Valves

The piston can be used up to a 4° inclination.

• Drive Mechanisms & Components

• Cylinders

A valve used to open and close a circuit. A mechanism is adopted that allows smooth handle operation even when pressurized. (Ex...

• Valves

• Stop Valves

Since it is a universal screw type, it can be installed in narrow spaces. ASBG100-400M-U contains silicone that is resistant to...

• Meters & Instruments

• Pressure Gauges

This is an electric pump that can boost the pressure up to 70MPa using tap water as the working fluid. It can be used with conf...

• Pumps

• High Pressure Pumps

• Drive Mechanisms & Components

• Cylinders

Various pulleys, gears, etc. can be easily removed. 2-jaw and 3-jaw types are available for 100kN, 200kN, and 500kN, respectively.

• Machining / Machine Tools

• Pullers

This is an ideal tool for closing the ends of copper pipes used in various air conditioners, refrigerators, etc. When combined ...

• Machining / Machine Tools

• Hydraulic Tools

Used for straightening the tip of coil rods, and for bending and straightening various rod materials.

• Machining / Machine Tools

• Hydraulic Tools