Furukawa Electric Manufacturing Co., Ltd.'s Company Profile and Products

This is a manual open/close type outdoor single pole single throw disconnect switch. Hang the operating rod on the hook of the ...

• Switches

• Disconnects

This is a manual open/close type indoor single-pole single-throw disconnector. Hang the operating rod on the hook of the blade ...

• Switches

• Disconnects

This is a manual open/close type outdoor single pole single throw disconnect switch. It is used in equipment that requires self...

• Switches

• Disconnects

This is a manual open/close type indoor single-pole single-throw disconnector. It is used in equipment that requires self-cooli...

• Switches

• Disconnects

This is an electromagnetic coil type indoor single-pole single-throw disconnector. Since it uses a toggle mechanism, there is n...

• Switches

• Disconnects

This is an indoor single-pole switching disconnect switch that can be opened and closed manually and uses a post insulator. Han...

• Switches

• Disconnects

This is an indoor double-pole single-throw disconnector that can be opened and closed manually. The contacts are turned on and ...

• Switches

• Disconnects

This is an electric motor-operated indoor double-pole switching disconnector used to switch single-phase circuits. Since it use...

• Switches

• Disconnects

Compared to the conventional grounding system, which uses a grounding rod for each phase, the structure allows all three phases...

• Clamps & Fasteners

• Earth Clamps

This is an electrically operated indoor three-phase bulk closing/disconnecting switch. It has an orthodox three-phase structure...

• Switches

• Disconnects

This is an air-operated indoor three-phase disconnect switch. It is possible to open and close each phase individually. The con...

• Switches

• Disconnects

This is an indoor 8-pole double-throw disconnector that can be switched to A side, B side, and neutral (double cut) by operatin...

• Switches

• Disconnects

The operating shaft is rotated 190 degrees using a DC geared motor to open and close. Mainly used to open and close horizontal ...

• Switches

• Disconnects

This is an operating device that opens and closes a disconnector of 36kV or less. A DC electric motor drives a worm gear via a ...

• Switches

• Disconnects

Used in combination with live terminal. The angle can be changed by 90 degrees, so when the live terminal is disconnected, it c...

• Terminals / Interfaces

• Flexible Terminals

Terminals can be disconnected and connected while working on live wires, eliminating the hassle of power outages. *Load current...

• Terminals / Interfaces

• Flexible Terminals

It is used to connect copper strips and electric wires, and the connection on the wire side is not compressed but tightened. Wh...

• Terminals / Interfaces

• Tabs

It can be used when connecting electric wires to the secondary terminals of transformers, making it easy to connect and disconn...

• Terminals / Interfaces

• Compression Terminal Lugs

A connector that connects the copper wires (main line and branch line) of the distribution line. By using a torque cap on the t...

• Connectors

• Relay Connectors

A connector for connecting low voltage drop-in lines. By using a torque cap on the tightening part, it has a structure that all...

• Connectors

• Relay Connectors

Used to connect high voltage overhead distribution lines and high voltage underline wires. When connecting to overhead power li...

• Connectors

• High Voltage Connectors

It is used to protect customer service lines and electrical equipment from short-circuit currents that occur in low-voltage ove...

• Safety Devices

• Fuses

Used for anchoring high-voltage overhead distribution lines (copper wires). There are three applicable sizes: 5mm, 60m㎡, and 1...

• Clamps & Fasteners

• Cable Clamp

Insert into the end of stranded copper wire and use to prevent the wire from warping during tightening. There are seven applica...

• Protective Materials & Equipment

• Cable Glands

It is said to be a three-tiered cubicle because it is a closed cubicle with one barrier installed at the top, middle, and botto...

• Controllers

• Control Panels

The live parts are isolated in a box with a factory-molded angle frame. The front and back sides are mesh-shaped, so you can vi...

• Controllers

• Control Panels

This is a distribution board for supplying power to lights, outlets, power circuits, etc. We can manufacture products according...

• Controllers

• Control Panels

This is an electrically operated indoor single-pole disconnect switch. It can be opened and closed automatically using an elect...

• Controllers

• Control Panels

This is a peeler that strips the coating of 6.6kV high voltage cross-linked polyethylene insulated wire (PDC). Applicable wire ...

• Machining / Machine Tools

• Wire Processing Systems

This is a stripper that can strip the sheathing of 6.6KV high-voltage wires to any length. Applicable wire sizes are OE5mm, OC-...

• Machining / Machine Tools

• Wire Processing Systems

A peeler for stripping the coating of low-voltage watertight electric wires. The purpose is to strip the insulation from the mi...

• Machining / Machine Tools

• Wire Processing Systems

This is a peeler exclusively for IV and DV lines. The purpose is to strip the insulation from the middle part of the wire (stri...

• Machining / Machine Tools

• Wire Processing Systems

Protects worker's face during live wire construction during instrumentation work. The mask can be attached to and removed from ...

• Safety Devices

• Safety Devices

To ensure safety during power outage work, such as for electrical equipment and electrical circuits, we use air switches (AS), ...

This is an earth hook mainly used inside cubicles. When installed, the structure allows tightening by simply turning the operat...

Used in conjunction with a resistance reducer when grounding utility poles. After developing the pole into a rhombic shape with...