V100 vibration measuring instrument
Unipulus
About This Product
The V100 is a vibration measuring instrument that can measure the vibration at the time of machine processing, display the amplitude, determine the threshold, and record the measurement data.
■ Extracting vibration components by bandpass filter
Removes unnecessary noise components from vibration waveforms
■ Removal of noise components by band eliminated filter
Remove only unique frequency components such as induced noise
■ Vibration detection mode
Vibration value mode, envelope mode, peak value mode, effective value mode, wave high mode, waveform rate mode
■ Comparing the measurement results and the set value of the upper and lower limit, judging output is possible.
HH, Hi, OK, Lo, LL
■ Family diagnostic function of input waveform by FFT
Simple monitoring of frequency changes in vibration input waveforms with the FFT spectrum. By confirming which frequency area has changed, it is possible to detect the abnormalities of the device that is difficult to judge with the time axis waveform.
■ Save measurement results: internal memory
It is memorized 50 times for each work and monitor is possible.
Save data: Time/measurement value/unit/temperature/judgment result/vibration detection mode/hold mode
■ Graph data storage: internal memory
I remember the measured waveform data for the past 16 times and monitor
■ Save measurement results: SD card (CSV format)
Save about 65,000 times for each work
■ Measurement waveform storage: SD card (CSV format)
Save input waveforms (every wavy or NG waveform) 100 times
■ Save FFT screen: SD card (BMP format)
Save screen data 100 times
-
Product
V100 vibration measuring instrument
-
Handling Company
Unipulus
-
Categories
1 Models of V100 vibration measuring instrument
| Product Image | Part Number | Price (excluding tax) | Analog club analog filter | Analog club monitor output | Analog portion applied voltage | Analog section A / D converter | Analog section signal input range | Display display | Display portion small number | Display unit | External signal input (11 points) | External signal output (9 points) | General performance external dimensions | General performance power consumption | General performance power supply voltage | General performance rush current (TYP) | General performance usage conditions | General performance weight | Indicated portion indicated value display range | Interface | Number of display portions displayed | Operation unit input instrument | Record record data | Recording department recording media | Temperature measurement | Vibration diagnostic part vibration analysis (FFT) | Vibration diagnostic portion vibration detection | accessories |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
V100 |
Available upon quote | Select from the primary loop filter cut -off frequency 30, 100, 1k Hz | Output level: Approximately 1 V (approx. 1 V / g) per 50 MV (about 1 V / g) load resistance: 2 kΩ or more | DC 5 V ± 10 % output current: within 30 mA | Speed: 2,000 times / second resolution ability: 24 Bit (binary) Effective resolution ability: about 1/10,000 for 150 MV | ± 150 MV (UNA02 can be measured up to MAX3 G) | 3.5 inch STN Color LCD display area: 71 (W) × 53 (H) mm dot configuration: 320 × 240 dot | 0 / 0.0 / 0.00 / 0.000 | None, m / s2, mm / s2, mm / s, mm / s, mm, μm, % | Hold control (T / H, Section), graph control (Graph Trig), FFT control (FFT TRIG), work selection (WORK0 -Work3), comparative values (Cal0, cal1), Operation prohibited (Lock) Voltage input circuit (plus komon / minus comon shared) On -on. Pressure: DC 12 V or more, OFF voltage DC 3 V or less, Steering current: about 5 mA (during DC 24 V), insulating method: Photoba plastic instruction | Comparison result (HH, Hi, OK, Lo, LL), hold completion (Hold end), normal operation (RUN), graph drawing (EVENT), SD card normal (SD Card), open collector output circuit (sync type plus comon input equipment connection possible), rated voltage: DC 30 V, rated voltage. Current: 30 mA or less, insulating method: Photobapura instructions | 99.5 (W) x 96 (H) x 117.3 (d) mm (not included) | 7 W type | DC 24 V (± 15 %) | 2 a, 10 msec (at room temperature, cold start) | Used temperature range 0 ° C to +40 ° C / storage temperature range -20 ° C to + 60 ° C humidity 85% RH or less (condensation not possible) | Approximately 1.0 kg | 4 digits ± 9,999 | RS-232C communication interface | 3 times / second fixed | Analog type touch panel | Measurement waveform data (up to 99.9 seconds 100 files) Measurement result data (10 files 1 file for each work ≒ 5 MB 65,530 times) FFT screen data (100 files) | SD card | Record the temperature at the time of vibration measurement (history, SD card) Temperature measurement range: -10 ° C to + 90 ° C, accuracy: ± 1.5 ° C, decomposition ability: 0.01 ° C. | Sampling magnification: 1x / 2 times / 4 times / 8 times window function: square / honey / humming / blackman analysis mode: Average vibration value / envelope (moving average per frequency) display range: 99.9 DBMAX display mode: continuous / single -shot | Breaking filter: High pass filter 1-500 Hz Low Pass filter 1-500 Hz (secondary buttower characteristic digital filter) Configuration: 16 patterns (switched by external input and communication) | Instruction manual, connector for external input / output, SD card, acceleration sensor, temperature sensor |
Customers who viewed this product also viewed
Other products of Unipulus
![Road cell [For load measurement] Ultra -thin compressed load cell UST-Unipulus](https://metoree.s3.ap-northeast-1.amazonaws.com/img/products-new/30004442023062169.png)
View more products of Unipulus
About Company Handling This Product
- Japan