Hoshin Electronics Co., Ltd.

12bit A/D converter module with 8ch successive approximation sample hold ■Features ・The analog input has a sample hold funct...

The peak voltage of the analog signal is digitized by the ADC. It supports gate widths from 500ns, so it can also handle high-s...

The peak voltage of the analog signal is digitized by the ADC. It supports gate widths from 500ns, so it can also handle high-s...

This interface is for using the CAMAC crate controller with a PC (computer). It can also be used as an interface for VME, F-BUS...

4 models listed

■Features ・Multi-channel scaling module that counts pulse signals (NIM level or TTL level) from radiation in time units (10μs ...

DC voltage output module ■ Features ・Maximum output current 100mA ・Output voltage (switchable for each channel) 0V to +10V, ...

Ideal for signal amplification of photomultipliers for photoelectric conversion of scintillation counters and Chilenkov counter...

■Features ・Spectrometer for emission spectroscopy that allows instant computer analysis ・Small and lightweight type with inte...

CC-D05 is a CCD line sensor with a high-speed clock rate of 1MHz, which converts 512 pixels and 1,024 pixels of data into 12BIT...

A multi-channel analyzer that can be directly connected to a PC (computer). Connect with the included USB cable, so you can use...

12bit counter type time interval measurement module with internal clock of 200MHz ■Features ・Achieved a time accuracy of 5ns ...

■Features Power supply for driving piezoelectric elements such as piezo elements

■Easily control CAMAC crate with PC CCP-F allows you to easily control modules in the CAMAC crate and collect data using a PC. ...

This module outputs NIM pulses when there are more than a set number of simultaneous input signals. Ideal for high energy exper...

■Features A two-system conversion module that converts 8-input TTL signals to NIM signals and 8-input NIM signals to TTL signal...

A module that outputs a pulse with a specified width delayed by a specified time from the start signal. ■Features ・The delay ...

This module outputs a digital NIM signal with a set width when the analog signal exceeds a threshold. ■Features ・Uses a compa...

This module is a test module for A/D converters. There are PULSE OUT and CHARGE OUT outputs. PULSE OUT outputs the output volta...

Effective for debugging VME modules and understanding the status of VME modules ■ Features ・Direct LED display of VME bus dat...

A compact unit with one built-in charge amplifier hybrid IC (NO12-1). It is also very convenient when using N012-1 for the firs...

■Features ・Ideal for gamma ray detection ・Convert CsI10×10×10mm into electrical signal with pin photo sensor ・Built-in pream...

Module for adjusting delay time of timing signals, etc. ■Features The input NIM standard logic signal is delayed by 105ns and ...

Amplify small signals to A/D converter level ■Features ・Amplify electrical signals from DC to 20kHz by 10 to 1000 times ・Out...

Ideal as a NIM test signal ■Features ・Highly stable oscillation by crystal oscillation ・All outputs are NIM level (N010-T if...

Shaping charge amplifier output and converting pulse for peak hold ■Features ・3-stage integral shaper amplifier ・Time consta...

Halve the voltage of signals such as counters and output from two connectors. ■Features ・Convert the 50Ω signal into two 50Ω ...

Outputs high-speed analog pulses as integrated pulses with a time constant of 150 ns. ■Features ・Ideal for scintillation coun...

Ideal for fast triggers ■Features 50Ω NIM input signal can be used as 8 inputs x 2ch or 16 inputs x 1ch using the FAN IN/OUT f...

■Features Displays CAMAC address and data bus status on LED, automatically selects data READ and WRITE ■Specifications Display...

■Features ・Adding 4 input linear signals ・Output from two NIM connectors ・Input impedance 50Ω ・Output impedance 50Ω ・Rise ...